dsPIC33FJXXXMCX06A/X08A/X10A
16-bit Digital Signal Controllers (up to 256 KB Flash and
30 KB SRAM) with Motor Control and Advanced Analog
Operating Conditions
Timers/Output Compare/Input Capture
• Up to nine 16-bit timers/counters. Can pair up to
make four 32-bit timers.
• 3.0V to 3.6V, -40ºC to +150ºC, DC to 20 MIPS
• 3.0V to 3.6V, -40ºC to +125ºC, DC to 40 MIPS
• Eight Output Compare modules configurable as
timers/counters
Core: 16-bit dsPIC33F CPU
• Eight Input Capture modules
• Code-efficient (C and Assembly) architecture
• Two 40-bit wide accumulators
Communication Interfaces
• Two UART modules (10 Mbps)
• Single-cycle (MAC/MPY) with dual data fetch
• Single-cycle mixed-sign MUL plus hardware
divide
- With support for LIN 2.0 protocols and IrDA®
• Two 4-wire SPI modules (15 Mbps)
• Up to two I2C™ modules (up to 1 Mbaud) with
SMBus support
Clock Management
• ±2% internal oscillator
• Up to two Enhanced CAN (ECAN) modules
(1 Mbaud) with 2.0B support
• Programmable PLLs and oscillator clock sources
• Fail-Safe Clock Monitor (FSCM)
• Independent Watchdog Timer (WDT)
• Fast wake-up and start-up
• Quadrature Encoder Interface (QEI) module
• Data Converter Interface (DCI) module with I2S
codec support
Power Management
• Low-power management modes (Sleep, Idle,
Doze)
Input/Output
• Sink/Source up to 10 mA (pin specific) for stan-
dard VOH/VOL, up to 16 mA (pin specific) for non-
standard VOH1
• Integrated Power-on Reset and Brown-out Reset
• 1.35 mA/MHz dynamic current (typical)
• 55 μA IPD current (typical)
• 5V-tolerant pins
• Selectable open drain, pull-ups, and pull-downs
• Up to 5 mA overvoltage clamp current
• External interrupts on all I/O pins
Motor Control PWM
• Up to four PWM generators with eight outputs
• Dead Time for rising and falling edges
• 12.5 ns PWM resolution
Qualification and Class B Support
• AEC-Q100 REVG (Grade 1 -40ºC to +125ºC)
• AEC-Q100 REVG (Grade 0 -40ºC to +150ºC)
• Class B Safety Library, IEC 60730
• PWM support for Motor Control: BLDC, PMSM, ACIM,
and SRM
• Programmable Fault inputs
• Flexible trigger for ADC conversions and configurations
Debugger Development Support
• In-circuit and in-application programming
• Two program and two complex data breakpoints
• IEEE 1149.2-compatible (JTAG) boundary scan
• Trace and run-time watch
Advanced Analog Features
• Two ADC modules:
- Configurable as 10-bit, 1.1 Msps with four
S&H or 12-bit, 500 ksps with one S&H
- 18 analog inputs on 64-pin devices and up to
32 analog inputs on 100-pin devices
• Flexible and independent ADC trigger sources
Packages
Type
QFN
TQFP
TQFP
TQFP
Pin Count
Contact Lead/Pitch
I/O Pins
64
0.50
64
0.50
80
0.50
100
0.40
53
53
69
85
Dimensions
9x9x0.9
10x10x1
12x12x1
14x14x1
Note: All dimensions are in millimeters (mm) unless specified.
2009-2012 Microchip Technology Inc.
DS70594D-page 1