DS28E04-100
4096-Bit Addressable 1-Wire EEPROM
with PIO
www.maxim-ic.com
GENERAL DESCRIPTION
FEATURES
®
Sꢀ 4096 bits of EEPROM Memory Partitioned into
16 Pages of 256 Bits
The DS28E04-100 is a 4096-bit, 1-Wire EEPROM
chip with seven address inputs. The address inputs
are directly mapped into the 1-Wire 64-bit Device ID
Number to easily enable the host system to identify
the physical location or functional association of the
DS28E04-100 in a multidevice 1-Wire network en-
vironment. The 4096-bit EEPROM array is configured
as 16 pages of 32 bytes with a 32 byte scratchpad to
perform write operations. EEPROM memory pages
can be individually write protected or put in EPROM-
emulation mode, where bits can only be changed
from a 1 to a 0 state. In addition to the memory, the
DS28E04-100 has two general-purpose I/O ports that
can be used for input or to generate level and/or
pulse outputs. Activity registers also capture port
activity for state change monitoring. The DS28E04-
100 communicates over the single-contact 1-Wire
bus. The communication follows the standard Dallas
Semiconductor 1-Wire protocol.
Sꢀ Seven Address Inputs for Physical Location
Configuration
Sꢀ Two General-Purpose PIO Pins with Pulse-
Generation Capability
Cꢀ Individual Memory Pages can be Permanently
Write-Protected or put in OTP EPROM-
Emulation Mode (“Write to 0”)
Cꢀ Communicates to Host with a Single Digital
Signal at 15.3kbps or 111kbps Using 1-Wire
Protocol
Cꢀ Parasitic or VCC Powered
Cꢀ Conditional Search Based on PIO Status or PIO
Activity
Cꢀ Switchpoint Hysteresis and Filtering to Optimize
Performance in the Presence of Noise
Cꢀ Reads and Writes Over a Wide 2.8V to 5.25V
Voltage Range from -40°C to +85°C
Cꢀ 16-Pin, 150-mil SO Package
APPLICATIONS
Sꢀ Autoconfiguration of Modular Systems such as
Central-Office Switches, Cellular Base Stations,
Access Products, Optical Network Units, and
PBXs
ORDERING INFORMATION
PART
TEMP RANGE PIN-PACKAGE
-40°C to +85°C 16 SO (150 mils)
DS28E04S-100
DS28E04S-100/T&R -40°C to +85°C Tape-and-Reel
Sꢀ Accessory/PCB Identification
PIN CONFIGURATION
TYPICAL OPERATING CIRCUIT
A3
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
IO
VCC
RPUP
A2
A4
PX.Y
A1
A5
A6
A0
A6
A0
IO VCC
POL
IO VCC
POL
A0
A6
µC
P1
P0
P1
P0
GND
N.C.
VCC
POL
GND
N.C.
P1
LED
GND
GND
DS28E04 #1
RST1 RST0 DS28E04 #7
P0
SO (150 mils)
Commands, Registers, and Modes are capitalized for
clarity.
1-Wire is a registered trademark of Dallas Semiconductor Corp.
Note: Some revisions of this device may incorporate deviations from published specifications known as errata. Multiple revisions of any device
may be simultaneously available through various sales channels. For information about device errata, click here: www.maxim-ic.com/errata.
1 of 36
REV: 102704