DPF950 SERIES
Dual output
• 950W front e nd
• EN61000-3-2 compliant
• 12.75 x 8.0 x 4.93 inch (including pane l)
• Hot-pluggable , N+1 re dundancy
• Full s e t of s tatus s ignals
• EN55022, EN55011 conducte d e mis s ions le ve l B
• UL, VDE, CSA and BABT s afe ty approvals
The DPF950 is a 950W universal input AC/DC front end power supply in a fully
enclosed hot pluggable case with built-in fan, front panel with handle, IEC input
connector, on/off switch and DIN output signal connector. Providing dual 48V
and 5V outputs with a full set of status signals, the DPF950 is designed as a
slot-in front end for distributed power systems. The DPF950 provides 950W of
output power and is fully compliant with EN61000-3-2. Standard features
include current sharing and full protection against overvoltage, overload and
short circuit. Remote or local system monitoring is possible via a full set of
status signals that include fan fail, DC good, remote inhibit and current
monitoring. The DPF950, with full international safety approval and the CE mark,
meets conducted emissions EN55022 level B. The DPF950 is designed for use
as a front end in medium power communication applications adopting
distributed power architecture. The DPF950 can be used in conjunction with our
complete range of 3 to 200W DC/DC converters to fully configure a distributed
power system.
[ 2 YEAR WARRANTY ]
SPECIFICATION All specifications are typical at nominal input, full load at 25°C unless otherwise stated
OUTPUT SPECIFICATIONS
EMC CHARACTERISTICS
Voltage set point
-46.5V ±0.50V
Radiated noise
EN55022/11, FCC part 15
EN55022/11
FCC part 15
Level A
Level B
Conducted noise
Total regulation
(Full load to no load)
Main output
Auxiliary output
±5.0%
±2.5%
Level A
Harmonic current emm. EN61000-3-2
Compliant
Electrical fast
transients/bursts
EN61000-4-4
Level 3
Rise time
At turn-on
3.0s, max.
Surge susceptibility
EN61000-4-5
Level 3
Transient response
Main output
50% to 100%
step at 1.0A/µs
3V max. dev.,
1ms recovery
to 1.0%
GENERAL SPECIFICATIONS
Hold-up time
Efficiency
120VAC, 60Hz FL
20ms @ 950W
78% min.
Ripple and noise
Main output
480mV pk-pk,
50mV pk-pk
0Hz to 30MHz (Note 5) Auxiliary output
Overvoltage protection latching
Output power limit
90Vin, >66% rated load
-55V to - 60V
950W
Isolation voltage
Input/output
Input/chassis
3000VAC
1500VAC
Switching frequency
50kHz
Short circuit protection Cyclic operation
Auto recovery
Approvals and
standards
VDE0805, EN60950, IEC950
UL1950, BABT
Current sharing
3V droop, 1/3 Load
to full load
±10% sharing
above 5A load
CSA C22.2 No. 950
INPUT SPECIFICATIONS
Input voltage range
Input frequency range
Input surge current
Input surge
Weight
MTBF
6.4kg (14Ibs)
90 to 264VAC
47Hz to 63Hz
MIL-HDBK-217F
@ 25°C
100,000 hours
ENVIRONMENTAL SPECIFICATIONS
220VAC, cold start @ 25°C
300VAC
36A typ.
20ms
Thermal performance
Operating ambient, FL 0°C to +50°C
Non-operating
-40°C to +70°C
50°C to 70°C ambient,
convection cooled
Derate to
50% load
Safety ground
leakage current
120VAC, 60Hz
230VAC, 50Hz
0.2mA
0.4mA
Cooling
Built-in fan
Input current
Input fuse
90VAC, 950W
14A rms max.
250VAC, 20A
Relative humidity
Altitude
Non-condensing
5% to 85% RH
UL, IEC approved
Operating
Non-operating
10,000 feet max.
40,000 feet max.
Power factor
110VAC
220VAC
0.99
0.98
Vibration
Shock
5Hz to 500Hz
MIL-STD-810E
2.4G rms peak
516.4 Part IV
PAGE 1