Digital Pressure Sensor DP-0SERIES
709
FIBER
PRECAUTIONS FOR PROPER USE
Refer to p.1566 for general precautions.
SENSORS
LASER
Connection
SENSORS
• Never use this product as a sensing device
for personnel protection.
• In case of using sensing devices for
personnel protection, use products which
meet laws and standards, such as OSHA,
ANSI or IEC etc., for personnel protection
applicable in each region or country.
How to connect
PHOTO-
ELECTRIC
SENSORS
Release lever
• Insert the cable with connector
CN-14A(-R)‑C□ into this product’s
connection connector section as shown
in the right figure.
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
• This product is used for non-corrosive gas.
The product shall not be used for liquid
or corrosive gas. Never use fluids having
inflammability, toxicity, etc., that affect the
human body, either.
How to disconnect
CURTAINS
/
SAFETY
• Pressing the release lever of the cable
with connector, pull out the connector.
COMPONENTS
Cable with connector
CN-14A(-R)-C□
PRESSURE /
FLOW
SENSORS
Note: Do not pull by holding the cable without pressing the release lever, as
INDUCTIVE
PROXIMITY
SENSORS
this can cause cable break or connector break.
PARTICULAR
USE
Part description
Factory setting
SENSORS
Digital display unit
Type
Low pressure type
High pressure type
ON mark
SENSOR
OPTIONS
Operation setting
NO/NC setting
Threshold value
Pressure unit
EASY mode
Connecting
connector
OFF mark
SIMPLE
WIRE-SAVING
UNITS
Key lock mark
NC
−50.0
kPa
NO
0.500
MPa
OVER mark
WIRE-SAVING
SYSTEMS
Pressure port
(M5 female thread)
Mode
selection key
MEASURE-
MENT
Setting value UP key
Setting value DOWN key
Display color
Red when ON, White when OFF
2.5 ms
SENSORS
Response speed
STATIC
CONTROL
DEVICES
Piping
• When using this product, connect a joint available in the market
to the pressure port. At the time, the tightening torque should be
1.0 N·m or less.
LASER
Error indication
MARKERS
Error indication
Description
Remedy
PLC
The load is short-circuited
causing an overcurrent to
flow.
Mounting
Turn OFF the power and
check the load.
HUMAN
MACHINE
INTERFACES
• Use sensor mounting bracket MS-DP1-1 prepared
independently.
When mounting this product with sensor mounting bracket, etc.,
the tightening torque should be 0.5 N·m or less.
ENERGY
MANAGEMENT
SOLUTIONS
Applied pressure at the
pressure port should be
Pressure is applied during brought to atmospheric
zero point adjustment.
FA
pressure and zero-point
adjustment should be done
again.
COMPONENTS
MACHINE
VISION
M3 (length 6 mm 0.236 in)
screws with washers
The applied pressure
exceeds the upper limit of
the displayed pressure
range.
SYSTEMS
(Accessory with MS-DP1-1)
UV
CURING
Applied pressure range
should be brought within
the rated pressure range.
SYSTEMS
The applied pressure
exceeds the lower limit
(back pressure) of the
displayed pressure range.
Sensor mounting
bracket MS-DP1-1
(Optional)
Selection
Guide
When other error massage is displayed, contact us.
Pressure/
Digital Display
Others
• Panel mounting bracket MS-DP1-8 (optional) and front protection
cover MS-DP1-3 (optional) are available.
Pressure/
Head-separated
• This product has been developed / produced for industrial use
only.
• The product shall be used only within the rated pressure range.
• Do not apply pressure exceeding the pressure resistance.
Otherwise, destruction of diaphragm occurs, preventing the
product to perform normal operation.
• Do not use during the initial transient time (0.5 sec.) after the
power supply is switched ON.
• The specification may not be satisfied in a strong magnetic field.
• This product is suitable for indoor use only.
• Take care that strong impact such as fall is not given to this
product. Otherwise, it may be destroyed.
• Avoid dust, dirt, and steam.
• Take care that the product does not come into contact with
organic solvents such as thinner.
• Take care that the product does not come into contact with oil or
grease.
• Take care that the product does not come into contact with
strong acid or alkaline.
Flow
• For the method for mounting panel mounting bracket, refer to the
instruction manual that came with the MS-DP1-8.
DP-0
DP-100
DP-M
Wiring
• Make sure that the power supply is OFF while performing the
wiring operation.
• Verify that the supply voltage variation is within the rating.
• If power is supplied from a commercial switching regulator,
ensure that the frame ground (F.G.) terminal of the power supply
is connected to an actual ground.
• In case noise generating equipment (switching regulator, inverter
motor, etc.) is used in the vicinity of this product, connect the
frame ground (F.G.) terminal of the equipment to an actual
ground.
• When extending the cable, use a cable whose conductor cross-
section area is 0.3 mm2 or more. The cable can be extended to
up to 10 m 32.808 ft in total length.
• Do not run the wires together with high-voltage lines or power
lines or put them in the same raceway. This can cause
malfunction due to induction.
• Do not apply stress directly to the connection cable leader or to
the connector.
• Do not insert wire into the pressure port. Otherwise, destruction
of diaphragm occurs, preventing the product to perform normal
operation.
5秒后页面跳转
资料手册解读：UC3842参数和管脚说明
一文带你了解无源晶振的负载电容为何要加两颗谐振电容CL1和CL2
玻璃管保险丝与陶瓷管保险丝：区别与替代性探讨
PCF8574资料解读：主要参数分析、引脚说明
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
