Digital Pressure Sensor DP-0SERIES
707
FIBER
SPECIFICATIONS
SENSORS
LASER
SENSORS
Type
Low pressure
DP-001
High pressure
DP-002
PHOTO-
ELECTRIC
SENSORS
NPN output
Item
PNP output
CE marking directive compliance
Type of pressure
DP-001-P
DP-002-P
MICRO
PHOTO-
ELECTRIC
SENSORS
EMC Directive, RoHS Directive
Gauge pressure
AREA
SENSORS
Rated pressure range
−100.0 to +100.0 kPa
0.000 to +1.000 MPa
SAFETY LIGHT
CURTAINS
/
−101.0 to +101.0 kPa
−1.030 to +1.030 kgf/cm2
−1.010 to + 1.010 bar
−14.65 to +14.65 psi
−756 to +756 mmHg
SAFETY
−0.010 to +1.010 MPa
−0.1 to +10.30 kgf/cm2
−0.1 to + 10.10 bar
−0.1 to +146.5 psi
COMPONENTS
PRESSURE /
FLOW
Set pressure range
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
Pressure withstandability
Applicable fluid
500 kPa
1.5 MPa
PARTICULAR
USE
Air, non-corrosive gas
SENSORS
Low pressure type: kPa, kgf/cm2, bar, psi, mmHg High pressure type: MPa, kgf/cm2, bar, psi
12 to 24 V DC ±10 % Ripple P-P 10 % or less
Selectable unit
SENSOR
OPTIONS
Supply voltage
SIMPLE
WIRE-SAVING
UNITS
Power consumption
30 mA or less
<NPN output type>
<PNP output type>
NPN open-collector transistor
• Maximum sink current: 50 mA
• Applied voltage: 30 V DC or less
(between comparative output and 0 V)
• Residual voltage: 2 V or less (at 50 mA sink current)
PNP open-collector transistor
• Maximum source current: 50 mA
• Applied voltage: 30 V DC or less
(between comparative output and +V)
• Residual voltage: 2 V or less (at 50 mA source current)
WIRE-SAVING
SYSTEMS
Comparative output
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
Output operation
Hysteresis
Selectable either NO or NC by key operation
Minimum 2 digits (variable)
LASER
MARKERS
Repeatability
±0.2 % F.S. (within ±4 digits)
±0.4 % F.S. (within ±4 digits)
Response time
Short-circuit protection
Display
2.5 ms, 25 ms, 250 ms, selectable by key operation
Incorporated
PLC
HUMAN
MACHINE
INTERFACES
3 + 1/2 digits, 3-color (white / red / pink) LCD display (Display update period: 250 ms)
ENERGY
MANAGEMENT
SOLUTIONS
−101.0 to +101.0 kPa
−0.010 to +1.010 MPa
−1.030 to +1.030 kgf/cm2
−0.1 to +10.30 kgf/cm2
−1.010 to + 1.010 bar
−0.1 to + 10.10 bar
Displayable
pressure range
FA
−14.65 to +14.65 psi
−0.1 to +146.5 psi
COMPONENTS
−756 to +756 mmHg
MACHINE
VISION
Protection
Ambient temperature
Ambient humidity
Voltage withstandability
Insulation resistance
Vibration resistance
Shock resistance
IP40 (IEC)
SYSTEMS
0 to +50 °C +32 to +122 °F (No dew condensation allowed), Storage: -10 to +60 °C +14 to +140 °F
UV
CURING
SYSTEMS
35 to 85 % RH, Storage: 35 to 85 % RH
500 V AC for one min. between all supply terminals connected together and enclosure
50 MΩ or more with 500 V DC megger between all supply terminals connected together and enclosure
10 to 150 Hz frequency, double amplitude 0.75 mm 0.030 in or maximum acceleration 49 m/s2, in X, Y and Z directions for two hours each
Selection
Guide
100 m/s2 acceleration (10 G approx.) in X, Y and Z directions three times each
Pressure/
Digital Display
Pollution degree
2
Pressure/
Head-separated
Overvoltage category
Usable altitude
I
Flow
2,000 m 6,562 ft or less
Temperature characteristics
(+20 °C +68 °F standard)
+10 to +40 °C +50 to +104 °F: Within ±1 % F.S.
0 to +50 °C +32 to +122 °F: Within ±2.5 % F.S.
+10 to +40 °C +50 to +104 °F: Within ±2 % F.S.
0 to +50 °C +32 to +122 °F: Within ±5 % F.S.
DP-0
DP-100
DP-M
Grounding method
Pressure port
Floating
M5 female thread
Enclosure: PBT (glass fiber reinforced), LCD display: Acrylic, Pressure port: Brass (nickel plated)
Mounting threaded part: Brass, O-ring: Nitrile rubber (NBR), Key section: Polycarbonate
Material
Weight
25 g approx.
Accessory
CN-14A-C2 (Connector attached cable 2 m 6.562 ft): 1 pc.
Note: Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 °C +68 °F.