5W DC-DC Regulated Dual Output Converter
DCW05 series
Features :
2:1 wide input range
4:1 wide input range(option)
1000VDC I/O isolation
3000VDC I/O isolation(option)
Built-in EMI filter
Protections: Short circuit / Overload
Cooling by free air convection
Five-sided shield metal case
100% burn-in test
Low cost / High reliability
Approvals: FCC / CE
2 years warranty
SPECIFICATION
ORDER NO.
DCW05A-05 DCW05B-05 DCW05C-05 DCW05A-12 DCW05B-12 DCW05C-12 DCW05A-15 DCW05B-15 DCW05C-15
DC VOLTAGE
5V
12V
15V
CURRENT RANGE
100 ~ 500mA
46 ~ 230mA
38 ~ 190mA
RATED POWER
5W
5.5W
60mVp-p
5.7W
60mVp-p
RIPPLE & NOISE (max.) Note.2
50mVp-p
0.5%
OUTPUT
LINE REGULATION
LOAD REGULATION
VOLTAGE ACCURACY
Note.3
Note.4
0.5%
2.0%
SWITCHING FREQUENCY
VOLTAGE RANGE
50KHz min.
A: 9 ~ 18VDC B: 18 ~ 36VDC C: 36 ~ 72VDC
75% 77% 77% 80%
Full load A: 586mA B: 286mA C: 139mA
EFFICIENCY (Typ.)
82%
83%
81%
83%
85%
INPUT
DC CURRENT
No load A: 41mA B: 21mA
Pi network
C: 12mA
FILTER
Fuse recommended
PROTECTION
150 ~ 250% rated output load
OVERLOAD
Protection type : Shunt down o/p voltage, re-power on to recover
All output equipped with over current protection
Protection type : Shun down o/p voltage, re-power on to recover
-40 ~ +71 (refer to output load derating curve)
20% ~ 90% RH non-condensing
PROTECTION
SHORT CIRCUIT
WORKING TEMP.
WORKING HUMIDITY
-40 ~ +105 , 10 ~ 95% RH
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
ENVIRONMENT
0.03% /
(0 ~ 50 )
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
ISOLATION CAPACITANCE
I/P-O/P:1KVDC
I/P-O/P: 100M Ohms / 500VDC / 25 / 70% RH
80pF max.
SAFETY &
EMC
(Note. 5)
EMI CONDUCTION & RADIATION Compliance to EN55022 Class B, FCC part 15 Class B
Compliance to EN61000-4-2,3,4,5,6,8, light industry level, criteria A
900khrs min. MIL-HDBK-217F (25
EMS IMMUNITY
MTBF
)
OTHERS
DIMENSION
PACKING
31.8*20.3*12.2mm (L*W*H) or 1.25"*0.80"*0.48" inch (L*W*H)
15g
Pin Configuration
Derating Curve
Mechanical Specification
Unit:mm(inch)
4.6(0.18)
20.3(0.80)
3.8(0.15)
Pin No.
Output
100
80
2 & 3
9
-Vin
COM
-Vout
+Vout
COM
+ Vin
23
22
2
3
2.5(0.10)
5.0(0.20)
11
BOTTOM VIEW
14
16
16
14
9
22 & 23
11
-40
0
25
50 60 71
100
15.2(0.60)
0.6+ 0.1/-0(0.024)
12.2(0.48)
Ta (
)
1.All parameters are specified at normal input, rated load, 25 70% RH ambient.
NOTE
2.Ripple & noise are measured at 20MHz by using a 12" twisted pair terminated with a 0.1uf & 47uf capacitor.
3.Line regulation is measured from low line to high line at rated load.
4.Load regulation is measured from 20% to 100% rated load.
5.The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
File Name:DCW05-SPEC 2011-03-14