12W DC-DC Regulated Dual Output Converter
DCW12 series
Features :
2:1 wide input range
1500VDC I/O isolation
Built-in remote ON/OFF control
Built-in EMI filter
Protections: Short circuit / Overload
Cooling by free air convection
Five-sided shield metal case
100% full load burn-in test
Low cost / High reliability
2 years warranty
SPECIFICATION
ORDER NO.
DCW12A-05 DCW12B-05 DCW12C-05 DCW12A-12 DCW12B-12 DCW12C-12 DCW12A-15 DCW12B-15 DCW12C-15
DC VOLTAGE
5V
12V
15V
CURRENT RANGE
240 ~ 1200mA
100~ 500mA
80 ~ 400mA
RATED POWER
12W
RIPPLE & NOISE (max.) Note.2
50mVp-p
0.5%
60mVp-p
60mVp-p
OUTPUT
LINE REGULATION
LOAD REGULATION
VOLTAGE ACCURACY
Note.3
Note.4
0.5%
2.0%
SWITCHING FREQUENCY
VOLTAGE RANGE
400KHz min.
A: 9 ~ 18VDC B: 18 ~ 36VDC C: 36 ~ 72VDC
80% 80% 81% 84%
Full load A: 1245mA B: 625mA C: 320mA
84%
84%
83%
84%
83%
EFFICIENCY (Typ.)
INPUT
DC CURRENT
No load A: 70mA
Pi network
B: 35mA
C: 25mA
FILTER
Fuse recommended
PROTECTION
110 ~ 180% rated output load
OVERLOAD
Protection type : Hiccup mode, recovers automatically after fault condition is removed
All output equipped with over current protection
PROTECTION
Note.5
SHORT CIRCUIT
Protection type : Hiccup mode, recovers automatically after fault condition is removed
-25 ~ +71 (refer to output load derating curve)
WORKING TEMP.
20% ~ 90% RH non-condensing
WORKING HUMIDITY
-25 ~ +105 , 10 ~ 95% RH
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
ENVIRONMENT
0.05% /
(0 ~ 50
)
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
I/P-O/P:1.5KVDC
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
ISOLATION CAPACITANCE
I/P-O/P: 100M Ohms / 500VDC / 25 / 70% RH
2200pF max.
SAFETY &
EMC
EMI CONDUCTION & RADIATION Compliance to EN55022 Class A, FCC part 15 Class A
EMS IMMUNITY
REMOTE CONTROL
MTBF
Compliance to EN61000-4-2,3,4,5,6,8, light industry level, criteria A
Power ON: R.C. ~ -Vin > 4VDC or open ; Power OFF: R.C. ~ -Vin < 1VDC or short
600Khrs min. MIL-HDBK-217F (25
)
OTHERS
DIMENSION
PACKING
31.8*20.3*12.2mm (L*W*H) or 1.25"*0.80"*0.48" inch (L*W*H)
18.5g
Pin Configuration
Derating Curve
Mechanical Specification
Unit:mm(inch)
0.6 + 0.2/-0
20.3(0.80)
3.81(0.15)
Pin No.
Output
2.54(0.10)
1
100
60
1
2 & 3
9
R.C.
-Vin
23
22
2
3
2.54(0.10)
5.08(0.20)
SIDE
VIEW
COM
-Vout
+Vout
COM
+ Vin
BOTTOM VIEW
11
16
14
9
14
16
11
22 & 23
15.24(0.60)
-25
0
25
50 60 71
100
12.2(0.48)
Ta (
)
1.All parameters are specified at normal input, rated load, 25 70% RH ambient.
NOTE
2.Ripple & noise are measured at 20MHz by using a 12" twisted pair terminated with a 0.1uf & 47uf capacitor.
3.Line regulation is measured from low line to high line at rated load.
4.Load regulation is measured from 20% to 100% rated load.
5.Please prevent the converter from operating in overload or short circuit condition for more than 30 seconds.
File Name:DCW12-SPEC 2008-10-22