CY7C1141V18
CY7C1156V18
CY7C1143V18
CY7C1145V18
18-Mbit QDR™-II+ SRAM 4-Word Burst
Architecture (2.0 Cycle Read Latency)
Features
Functional Description
■ Separate Independent read and write data ports
❐ Supports concurrent transactions
■ 300 MHz to 375 MHz clock for high bandwidth
The CY7C1141V18, CY7C1156V18, CY7C1143V18, and
CY7C1145V18 are 1.8V Synchronous Pipelined SRAMs,
equipped with QDR™-II+ architecture. QDR-II+ architecture
consists of two separate ports to access the memory array. The
read port has dedicated data outputs to support read operations
and the write port has dedicated data inputs to support write
operations. QDR-II+ architecture has separate data inputs and
data outputs to completely eliminate the need to “turn-around”
the data bus required with common IO devices. Access to each
■ 4-Word Burst for reducing address bus frequency
■ DoubleDataRate(DDR)interfacesonbothreadandwriteports
(data transferred at 750 MHz) at 375 MHz
■ Read latency of 2.0 clock cycles
■ Two input clocks (K and K) for precise DDR timing
❐ SRAM uses rising edges only
■ Echo clocks (CQ and CQ) simplify data capture in high speed
port is accomplished through
a common address bus.
Addresses for read and write addresses are latched on alternate
rising edges of the input (K) clock. Accesses to the QDR-II+ read
and write ports are completely independent of one another. To
maximize data throughput, both read and write ports are
equipped with Double Data Rate (DDR) interfaces. Each
address location is associated with four 8-bit words
(CY7C1141V18), or 9-bit words (CY7C1156V18), or 18-bit words
(CY7C1143V18), or 36-bit words (CY7C1145V18) that burst
sequentially into or out of the device. Because data can be trans-
ferred into and out of the device on every rising edge of both input
clocks K and K, memory bandwidth is maximized while simpli-
fying system design by eliminating bus “turn-arounds”.
systems
■ Single multiplexed address input bus latches address inputs
for both read and write ports
■ Separate Port Selects for depth expansion
■ Data valid pin (QVLD) to indicate valid data on the output
■ Synchronous internally self-timed writes
■ Available in x8, x9, x18, and x36 configurations
■ Full data coherency providing most current data
[1]
■ Core VDD = 1.8V ± 0.1V; IO VDDQ = 1.4V to VDD
Depth expansion is accomplished with Port Selects for each port.
Port Selects enable each port to operate independently.
■ Available in 165-Ball FBGA package (13 x 15 x 1.4 mm)
■ Offered in both Pb-free and non Pb-free packages
■ Variable drive HSTL output buffers
All synchronous inputs pass through input registers controlled by
the K or K input clocks. All data outputs pass through output
registers controlled by the K or K input clocks. Writes are
conducted with on-chip synchronous self-timed write circuitry.
■ JTAG 1149.1 compatible test access port
■ Delay Lock Loop (DLL) for accurate data placement
Configurations
With Read Cycle Latency of 2.0 cycles:
CY7C1141V18 – 2M x 8
CY7C1156V18 – 2M x 9
CY7C1143V18 – 1M x 18
CY7C1145V18 – 512K x 36
Selection Guide
375 MHz
375
333 MHz
333
300 MHz
300
Unit
MHz
mA
Maximum Operating Frequency
Maximum Operating Current
1020
920
850
Note
1. The QDR consortium specification for V
is 1.5V + 0.1V. The Cypress QDR devices exceed the QDR consortium specification and are capable of supporting V
DDQ
DDQ
= 1.4V to V
.
DD
Cypress Semiconductor Corporation
Document Number: 001-06583 Rev. *C
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised June 15, 2007
[+] Feedback
5秒后页面跳转
NTC热敏电阻与PTC热敏电阻的应用原理及应用范围
GTO与普通晶闸管相比为什么可以自关断？为什么普通晶闸管不能呢？从GTO原理、应用范围带你了解原因及推荐型号
LF353数据手册解读：特性、应用、封装、引脚说明、电气参数及替换型号推荐
A4950资料手册解读：特性、应用、封装、引脚功能、电气参数及代换型号
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
