The Communications Edge TM
CV210-1A
Cellular-band Dual-Branch Downconverter
Product Information
Product Features
Product Description
Functional Diagram
• High dynamic range downconverter
The CV210-1A is a dual-channel high-linearity down-
converter designed to meet the demanding performance,
functionality, and cost goals of current and next generation
mobile infrastructure basestations. It provides high
dynamic range performance in a low profile surface-mount
leadless package that measures 6x6 mm square.
with integrated LO and IF amplifiers
28
27
26
24
23
22
25
RF/IF
N/C
GND
BIAS
GND
N/C
1
2
3
4
5
6
7
BIAS
GND
N/C
21
20
19
18
17
16
15
• Dual channels for diversity
• +30 dBm Input IP3
• +11.5 dBm Input P1dB
• RF: 800 – 915 MHz
IF Amp 1
GND
LO
It is ideally suited for high dynamic range receiver front
ends using diversity receive channels. Functionality
includes frequency conversion and IF amplification,
while an integrated LO driver amplifier powers the
passive mixer. The MCM is implemented with reliable
and mature GAs MESFET and InGaP HBT technology.
LPF LO Driver Amp
IF Amp 2
• IF: 65 – 120 MHz
GND
N/C
GND
N/C
• Single supply operation (+5 V)
• Pb-free 6mm 28-pin QFN package
• Low-side LO configuration
• Common footprint with other
PCS/UMTS/cellular versions
RF/IF
8
9
10
12
13
14
11
Typical applications include frequency downconversion
used in CDMA/GSM/TDMA, CDMA2000, W-CDMA,
and EDGE 2.5G and 3G mobile base transceiver stations.
Top View
Specifications (1)
Parameters
Units
MHz
MHz
MHz
%
Min
Typ
800 – 915
680 – 850
65 – 120
±7.5
75
10
±0.1
+30
+36.5
+11.5
10.5
0
Max
Comments
RF Frequency Range
LO Frequency Range
IF Center Frequency Range
% Bandwidth around IF center frequency
IF Test Frequency
SSB Conversion Gain
Gain Drift over Temp (-40° C to 85° C)
Input IP3
Input IP2
Input 1 dB Compression Point
Noise Figure
LO Input Drive Level
LO-RF Isolation
LO-IF Isolation
See note 2
See note 3
MHz
dB
dB
dBm
dBm
dBm
dB
dBm
dB
8
12
1.5
Temp = 25° C
Referenced to +25° C
See note 4
See note 4
See note 4
-1.5
+25
+33
See note 5
-2.5
+2.5
20
35
PLO = 0 dBm
PLO = 0 dBm
dB
Branch-Branch Isolation
Return Loss: RF Port
Return Loss: LO Port
Return Loss: IF Port
Operating Supply Voltage
Supply Current
dB
dB
dB
dB
56
15
20
16
V
+5
385
mA
°C / W
°C
320
475
27
160
Thermal Resistance
Junction Temperature
See note 6
1. Specifications when using the application specific circuit (shown on page 3) with a low side LO = 0 dBm and IF = 75 MHz in a downconverting application at 25° C.
2. IF matching components affect the center IF frequency. Proper component values for other IF center frequencies than shown can be provided by emailing to applications.engineering@wj.com.
3. The IF bandwidth of the converter is defined as 15% around any center frequency in its operating IF frequency range. The bandwidth is determined with external components. Specifications are valid around
the total ±7.5% bandwidth. ie. with a center frequency of 80 MHz, the specifications are valid from 80 ± 6 MHz.
4. Assumes the supply voltage = +5 V. IIP3 is measured with Δf = 1 MHz with RFin = -5 dBm / tone.
5. Assumes LO injection noise is filtered at the thermal noise floor, -174 dBm/Hz, at the RF, IF, and Image frequencies.
6. The maximum junction temperature ensures a minimum MTBF rating of 1 million hours of usage.
Absolute Maximum Rating
Ordering Information
Parameter
Rating
-40° to +85° C
-55° to +150° C
+5.5 V
Operating Case Temperature
Storage Temperature
DC Voltage
Part No.
CV210-1AF
Description
Cellular-band Dual-Branch Downconverter
(lead-free/RoHS-compliant 6x6mm QFN package)
CV210-1APCB75 Fully-Assembled Application Board, IF = 75MHz
Junction Temperature
+220 °C
Operation of this device above any of these parameters may cause permanent damage.
Specifications and information are subject to change without notice
WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: sales@wj.com • Web site: www.wj..com
Page 1 of 6 January 2006