CRCW...C e3
www.vishay.com
Vishay
Lead (Pb)-free Thick Film, Rectangular
Commodity Chip Resistors
FEATURES
• High volume product suitable for commercial
applications
• Stability (R/R 1 % for 1000 h at
70 °C)
• Lead (Pb)-free solder contacts on Ni barrier
layer
• Metal glaze on ceramic
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
STANDARD ELECTRICAL SPECIFICATIONS
LIMITING
ELEMENT
VOLTAGE
MAX. V
CASE
SIZE
CASE
SIZE
POWER RATING
TEMPERATURE
COEFFICIENT
ppm/K
RESISTANCE
RANGE
TOLERANCE
%
MODEL
P70 °C
E-SERIES
INCH METRIC
W
100
200
1
5
1R0 to 10M
1R0 to 10M
E24; E96
E24
0.063
50
CRCW0402...C
CRCW0603...C
CRCW0805...C
CRCW1206...C
0402 RR 1005M
Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 °C = 1.5 A
100
1
5
1R0 to 10M
1R0 to 10M
E24; E96
E24
0.10
75
0603 RR 1608M
0805 RR 2012M
1206 RR 3216M
200
Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 °C = 2.0 A
100
1
5
1R0 to 10M
1R0 to 10M
E24; E96
E24
0.125
150
200
Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 °C = 2.5 A
100
1
5
1R0 to 10M
1R0 to 10M
E24; E96
E24
0.25
200
200
Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 °C = 3.5 A
Notes
•
These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over
operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime
Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material
•
TECHNICAL SPECIFICATIONS
PARAMETER
UNIT
CRCW0402...C
CRCW0603...C
CRCW0805...C
CRCW1206...C
Rated dissipation at 70°C (1)
W
0.063
0.10
0.125
0.25
Limiting element voltage
V
50
75
150
200
U
max. AC/DC
Insulation voltage Uins. (1 min)
Insulation resistance
Category temperature range
Failure rate
V
> 75
> 100
> 200
> 300
> 109
°C
h-1
g
- 55 to + 155
0.1 x 10-9
Weight/1000 pieces
0.65
2
5.5
10
Note
(1)
The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the
printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded
Revision: 02-Nov-17
Document Number: 28773
1
For technical questions, contact: ff3aresistors@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000