D/CRCW-IF e3
www.vishay.com
Vishay
Pulse Proof Thick Film Chip Resistors
FEATURES
• High pulse performance, up to 10 kW
• Stability R/R 1 % for 1000 h at 70 °C
• AEC-Q200 qualified
• Material categorization: for definitions of
compliance please see www.vishay.com/doc?99912
STANDARD ELECTRICAL SPECIFICATIONS
LIMITING
POWER
ELEMENT
VOLTAGE
Umax.
CASE
SIZE
IMPERIAL
CASE
SIZE
METRIC
TEMPERATURE
COEFFICIENT
ppm/K
RESISTANCE
RANGE
RATING
P70
TOLERANCE
%
TYPE
SERIES
W
ACRMS/DC
V
5
10
5
D10/CRCW0402-IF
D11/CRCW0603-IF
D12/CRCW0805-IF
D25/CRCW1206-IF
CRCW1210-IF
0402
0603
0805
1206
1210
2010
2512
RR1005M
RR1608M
RR2012M
RR3216M
RR3225M
RR5025M
RR6332M
0.063
0.10
0.125
0.25
0.50
0.75
1.0
50
200
200
200
200
200
200
200
1.0 to 100K
1.0 to 100K
1.0 to 100K
1.0 to 100K
1.0 to 100K
1.0 to 100K
1.0 to 100K
E24
E24
E24
E24
E24
E24
E24
75
10
5
150
200
200
400
500
10
5
10
5
10
5
CRCW2010-IF
10
5
CRCW2512-IF
10
Notes
•
These resistors do not feature a limited lifetime when operated within the limits of rated dissipation, permissible operating voltage, and
permissible film temperature. However, the resistance typically increase due to the resistor’s film temperature over operating time, generally
known as drift. The drift may exceed the stability requirements of an individual application circuit and thereby limits the functional time.
Marking: See data sheet “Surface Mount Resistor Marking” (document number 20020).
•
•
Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material.
TECHNICAL SPECIFICATIONS
D10/
D11/
D12/
D25/
PARAMETER
UNIT
CRCW1210-IF CRCW2010-IF CRCW2512-IF
CRCW0402-IF CRCW0603-IF CRCW0805-IF CRCW1206-IF
Rated dissipation
P70
W
0.063
50
0.1
75
0.125
150
0.25
200
0.5
200
300
0.75
400
300
1.0
500
300
(1)
Operating voltage
max. ACRMS/DC
V
U
Insulation voltage
ins (1 min)
V
75
100
200
300
> 109
U
Insulation resistance
Operating temperature
range
°C
-55 to +155
Failure rate
Mass
h-1
< 0.1 x 10-9
10
mg
0.65
2
5.5
16
25.5
40.5
Note
(1)
The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the
printe-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded.
Revision: 17-Mar-15
Document Number: 20024
1
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000