CPC7591
Line Card Access Switch
provides the necessary functions to replace the
2-Form-C electromechanical ringing relay and it’s
associated snubber circuitry on traditional analog line
cards or contemporary integrated voice and data (IVD)
line cards found in Central Office (CO), Access and
PBX equipment. Because this device contains solid
state switches for tip and ring line break and for ringing
injection/return it requires only a +5 V supply for
operation and logic-level inputs for control. The
CPC7591 provides stable start up conditioning during
system power up and for hot plug insertion
Features
• TTL logic level inputs for 3.3V logic interfaces
• Smart logic for power up / hot plug state control
• Improved switch dv/dt immunity of 500 V/µs
• Small 16-pin SOIC or micro-leadframe package
• MLP package printed-circuit board footprint is 60
percent smaller than the SOIC version, 40 percent
smaller than fourth generation EMR solutions.
• Monolithic IC reliability
• Low, matched R
ON
• Eliminates the need for zero-cross switching
• Flexible switch timing for transition from ringing
mode to idle/talk mode.
applications. Once active, the inputs respond to
traditional TTL logic levels enabling the CPC7591 to
be used with 3.3V only logic.
• Clean, bounce-free switching
• Tertiary protection consisting of integrated current
limiting, voltage clamping, and thermal shutdown for
SLIC protection
• 5 V operation with power consumption < 10 mW
• Intelligent battery monitor
The CPC7591 is very similar to Clare’s CPC7581 with
the addition of defined start-up states and TTL
compatible logic inputs.
CPC7591xA and CPC7591xC versions include an
SCR that provides protection to the SLIC and
subsequent circuitry during a fault condition. The
CPC7591xC versions have a higher SCR hold current.
The CPC7591xB versions utilize clamping diodes to
• Latched logic-level inputs, no external drive circuitry
Applications
• VoIP Gateways
• Central office (CO)
• Digital Loop Carrier (DLC)
• PBX Systems
the V
pin to guard against negative fault transients.
BAT
Ordering Information
Specify CPC7591Bx for the SOIC package (47/tube)
and CPC7591Mx for the MLP (94/tube). Add “TR”,
sans quotes, to the part number for tape and reel
packaging. SOIC: 1000/reel or MLP: 2000/reel.
• Digitally Added Main Line (DAML)
• Hybrid Fiber Coax (HFC)
• Fiber in the Loop (FITL)
• Pair Gain System
• Channel Banks
Part Number Description
Description
CPC7591xA
CPC7591xB
Four-pole with protection SCR, tubes
Four-pole without protection SCR, tubes
The CPC7591 is a member of Clare’s next generation
Line Card Access Switch (LCAS) family. This
monolithic 4-pole solid state switch is available in
either a 16-pin SOIC or a 16-pin MLP package. It
Four-pole with protection SCR and higher
protection SCR hold current, tubes
CPC7591xC
Figure 1. CPC7591 Block Diagram
+5 Vdc
TRINGING
6
V
DD
7
CPC7591
XSW3
3
2 TBAT
TLINE
Tip
X
SW1
Secondary
Protection
SLIC
15 RBAT
SXW2
RLINE 14
Ring
L
A
T
C
H
XSW4
Switch
Control
Logic
10
11
VREF
INRINGING
LATCH
12
1
FGND
16
VBAT
9
DGND
8
RRINGING
SCR Trip Circuit
(CPC7591xA/C)
TSD
300Ω
(min.)
VBAT
RINGING
DS-CPC7591 - R01
www.clare.com
1