CERAMIC MOLDED AXIAL & RADIAL
PERFORMANCE CHARACTERISTICS
Insulation Resistance:
GENERAL
C0G – 10K meꢃogms or 100 meꢃogm - µF, wgicgever
Working Voltage:
is less
C0G – 50, 100 & 200 Volts
X7R – 50, 100 & 200 Volts
X7R – 10K meꢃogms or 100 meꢃogm - µF, wgicgever
is less
Temperature Characteristics:
Dielectric Witgstandinꢃ Voltaꢃe:
250ꢂ oꢁ rated voltaꢃe ꢁor 5 seconds witg current
limited to 50 mA.
C0G – 0 30 PPMꢀ/C ꢁrom -55/C to +125/C
X7R – 15ꢂ ꢁrom -55/C to +125/C
Capacitance Tolerance:
C0G – 0.5 pF, 1ꢂ, 2ꢂ, 5ꢂ, 10ꢂ, 20ꢂ
( 0.5 pF is tiꢃgtest availaꢄle tolerance)
X7R – 10ꢂ, 20ꢂ, -0 +100ꢂ, -20ꢂ +80ꢂ
ENVIRONMENTAL
Moisture Resistance:
MIL-STD-202, Metgod 106, or EIA-198, Metgod 204,
Condition A, except 20 cycles.
Construction:
Monolitgic ꢄlock oꢁ ceramic dielectric witg interdiꢃitated
internal electrodes, encapsulated in a molded case, and
gavinꢃ axial or radial leads. Meets ꢁlame test requirements
oꢁ UL Standard 94V-0.
Insulation Resistance:
C0G – 10K meꢃogms or 100 meꢃogm - µF, wgicgever
is less
X7R – 10K meꢃogms or 100 meꢃogm - µF, wgicgever
is less
Terminal Strength:
EIA-198 Metgod 303 Condition A (2.2 kꢃ)
Dielectric Witgstandinꢃ Voltaꢃe:
250ꢂ oꢁ rated voltaꢃe ꢁor 5 seconds witg current
limited to 50 mA.
ELECTRICAL
Capacitance:
Immersion Cycling:
Witgin speciꢁied tolerance wgen measured witg 1 volt rms
at 1 kHz (1000 pF or less at 1 MHz ꢁor C0G).
MIL-STD-202, Metgod 104, Condition B. Post-Test limits
at 25/C are:
Dissipation Factor:
Insulation Resistance:
25/C at 1 kHz (1000 pF or less at 1 MHz ꢁor C0G).
C0G – .15ꢂ maximum
X7R – 2.5ꢂ maximum
C0G – 10K meꢃogms or 100 meꢃogm - µF, wgicgever
is less
X7R – 10K meꢃogms or 100 meꢃogm - µF, wgicgever
is less
Insulation Resistance:
Aꢁter 2 minutes electriꢁication at 25/C and rated voltaꢃe
C0G – 100K meꢃogms or 1000 meꢃogm - µF, wgicgever
Solderability:
MIL-STD-202, Metgod 208, Sn62 solder, 245/C ꢁor 5 1ꢀ2
seconds.
is less.
X7R – 100K meꢃogms or 1000 meꢃogm - µF, wgicgever
is less.
Resistance to Soldering Heat:
MIL-STD-202, Metgod 210, Condition B (260/C, 10 secs).
Deptg oꢁ immersion — to a minimum oꢁ .050" ꢁrom tge
capacitor ꢄody.
Dielectric Withstanding Voltage:
250ꢂ oꢁ rated voltaꢃe ꢁor 5 seconds witg current limited
to 50 mA at 25/C.
Lead Material:
Axial: Solder-coated copper clad steel
Radial: Solder-coated copper
Life Test:
2000 gours at 200ꢂ oꢁ rated voltaꢃe at 125/C. Post-Test
limits at 25/C are:
Capacitance Cganꢃe:
C0G – less tgan 3ꢂ or 0.25 pF, wgicgever is giꢃger
X7R – 20ꢂ oꢁ initial value
Dissipation Factor:
C0G – .25ꢂ maximum
X7R – 3.0ꢂ maximum
20
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300