Datasheet
For Automotive 20 V Input 500 mA
Adjustable Output LDO Regulators
BDL00A5NUF-C BDL00A5EFJ-C
General Description
Key Specifications
The BDL00A5NUF-C and BDL00A5EFJ-C is a linear
regulator designed as a low current consumption product
for power supplies in various automotive applications.
This product is designed for up to 20 V as an absolute
maximum voltage and to operate until 500 mA for the
output current with low current consumption 30 µA (Typ).
The reference voltage accuracy (ADJ pin voltage
accuracy) is a very high accuracy (Note 1), ±2 %. The output
voltage can be adjusted between 1 V and 17 V by an
external resistive divider connected to the ADJ pin.
The output shutdown function is integrated in the devices.
A logical “HIGH” at the EN Pin turns on the device, and in
the other side, the device is controlled to disable by a
logical “LOW” input to the EN Pin.
◼ Wide Temperature Range (Tj):
◼ Operating Input Range:
◼ Current Consumption:
◼ Shutdown Circuit Current
◼ Output Current Capability:
◼ High ADJ Voltage Accuracy:
◼ Output Voltage:
-40 °C to +150 °C
2.9 V to 18 V
30 µA (Typ)
0 µA (Typ)
500 mA
±2 %
1 V to 17 V
(Note 3) It does not contain the current of external feedback resistance.
Applications
◼ Automotive (Power Train, Body ECU)
◼ Car Infotainment System, etc.
The device features the integrated Over Current Protection
to protect the device from a damage caused by a short-
circuiting or an overload. This product also integrates
Thermal Shutdown Protection to avoid the damage by
overheating.
Package
W (Typ) x D (Typ) x H (Max)
3.0 mm × 3.0 mm × 1.0 mm
4.9 mm × 6.0 mm × 1.0 mm
VSON10FV3030
HTSOP-J8
Furthermore, low ESR ceramic capacitors are sufficiently
applicable for the phase compensation.
(Note 1) The tolerance of feedback resistor is not included.
Features
◼ AEC-Q100 Qualified (Note 2)
◼ Functional Safety Supportive Automotive Products
◼ Output Shutdown Function (EN Function)
◼ Over Current Protection (OCP)
VSON10FV3030
HTSOP-J8
◼ Thermal Shutdown Protection (TSD)
(Note 2) Grade 1
Typical Application Circuit
◼ Components Externally Connected
(Note 4)
Capacitor: 1.0 µF ≤ CIN, 1.0 µF ≤ COUT
Resistor: 10 kΩ ≤ R2 ≤ 200 kΩ (Note 5)
VADJ (Typ): 0.75 V
푉푂푈푇
푅1 = 푅2 (
− ꢀ)
푉
퐴퐷퐽
VIN
VIN
VOUT
VOUT
VOUT
VIN
EN
VIN
CIN
COUT
VIN
CIN
COUT
R1
R2
R1
ADJ
ADJ
EN
VEN
VEN
R2
GND
GND
VSON10FV3030
HTSOP-J8
(Note 4) Electrolytic capacitor, tantalum capacitor and ceramic capacitors can be used. Set capacitor value which do not fall below CIN =1.0 µF,
COUT = 1.0 µF. These values need to consider the temperature characteristics and DC bias characteristics.
(Note 5) The tolerance of feedback resistor is not included in the accuracy of output voltage.
The value of a feedback resistor R2 must be within this range. R1 value is defined by following the formula using the limitation of R1.
〇Product structure : Silicon integrated circuit 〇This product has no designed protection against radioactive rays.
.
www.rohm.com
© 2020 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 14 • 001
TSZ02201-0BGB0A300120-1-2
05.Dec.2022 Rev.001
1/33