Technical Note
BD4157MUV
●Description of block operation
EN
With an input of 2.0 volts or higher, this terminal goes HIGH to activate the circuit, and goes LOW to deactivate the circuit
(with the standby circuit current of 40 μA), It discharges each output and lowers output voltage when the input falls to 0.8
volts or less.
V3_IN, V15_IN, and V3AUX_IN
These are the input terminals for each channel of a 3ch switch. V3_IN and V15_IN terminals have two pins each, which
should be short-circuited on the pc board with a thick conductor. A large current runs through these three terminals :
(V3_IN: 1.3A; V3AUX_IN: 0.275 A; and V15_IN: 0.65 A). In order to lower the output impedance of the connected power
supply, it is recommended that ceramic capacitors (with B-type characteristics or better) be provided between these
terminals and the ground. Specifically, the capacitors should be on the order of 1 μF between V3_IN and GND, and
between V15_IN and GND; and on the order of 0.1 μF between V3AUX_IN and GND.
V3, V15, and V3AUX
These are the output terminals for each switch. The V3 and V15 terminals have two pins each, which should be
short-circuited on the PC board and connected to an ExpressCard connector with a thick conductor, as short as possible.
In order to stabilize the output, it is recommended that ceramic capacitors (with B-type characteristics or better) be
provided between these terminals and the ground. Specifically, the capacitors should be on the order of 10 μF between V3
and GND, and between V15 and GND; and on the order of 1 μF between V3AUX and GND.
CPPE#
This pin is used to find whether or not a PCI-Express signal compatible card is present. Turns to “High” level with an
input of 2.0 volts or higher, which means that no card is provided, while it turns to “Low” level when the input is lowered to
0.8 volts or less, which means that a card is provided. Controls the ON/OFF, switch selecting the proper mode based on
the status of the system. Pull up resistance (100kΩ～200kΩ) is built into, so the number of components is reduced.
CPUSB#
This pin is used to find whether or not a USB2.0 signal compatible card is present. Turns to “High” level with an input of
2.0 volts or higher, which means that no card is provided, while it turns to “Low” level when the input is lowered to 0.8 volts
or less, which means that a card is provided. Controls the ON/OFF switch, selecting the proper mode based on the
system status. Pull up resistance (100kΩ～200kΩ) is built into, so the number of components is reduced.
SYSR
This pin is used to detect the system status. Turns to “High” level with an input of 2.0 volts or higher, which means that
the system is activated, while it turns to “Low” level when the input is lowered to 0.8 volts or less, which means that the
system is on standby.
PERST_IN#
This pin is used to control the reset signal (PERST#) to a card from the system side. (Also referred to as “SysReset#” by
PCMCIA.) Turns to “High” level with an input of 2.0 volts or higher, and sets PERST# to “High” AND with a “Power Good”
output. Turns to “Low” level and sets PERST# to “Low” when the input falls to 0.8 volts or less.
PERST#
This pin is used to send a reset signal to a PCI-Express compatible card. Reset status is determined by the outputs,
PERST_IN#, CPPE# system status, and EN on/off status. Turns to “High” level and activates the PCI-Express
compatible card only if each output is within the “Power Good” threshold, with the card inserted and PERST_IN# turned to
“High” level.
RCLKEN
This pin is used to send an enable signal to the reference clock. Activation status is determined by the outputs, CPPE#
system status, and EN on/off status. Turns to “High” level and activates the reference clock PLL only if each output is
within the “Power Good” threshold, with the card kept inserted.
TEST
This pin is used to test, which should be short-circuited to the GND. When it is short-circuited to V3AUX_IN, UVLO
(V3_IN, V15_IN) turns OFF.
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
2011.06 - Rev.A
8/24
5秒后页面跳转
深入解析CS8416引脚说明、参数、技术特点
TPA3116D2功放芯片参数详解、引脚说明
移位寄存器74HC165引脚说明、驱动程序示例解读
深入解析AD9833：DDS频率合成器的卓越性能与广泛应用
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
