5秒后页面跳转
AS8501 PDF预览

AS8501

更新时间: 2024-11-24 04:06:55
品牌 Logo 应用领域
艾迈斯 - AMSCO 传感器
页数 文件大小 规格书
40页 470K
描述
High precision voltage and current measurement sensor interface

AS8501 数据手册

 浏览型号AS8501的Datasheet PDF文件第2页浏览型号AS8501的Datasheet PDF文件第3页浏览型号AS8501的Datasheet PDF文件第4页浏览型号AS8501的Datasheet PDF文件第5页浏览型号AS8501的Datasheet PDF文件第6页浏览型号AS8501的Datasheet PDF文件第7页 
AS8501  
Preliminary Data Sheet  
High precision voltage and current measurement sensor interface  
REF  
AGND  
VDDA  
VSSA  
1
Features  
INTERNAL TEMPERATURE  
1.26 V  
REFERENCE  
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
16 bits resolution  
Differential inputs  
Single + 5V supply  
Low power 15 mW  
VDDD  
VSSD  
CALIBRATION  
DATA  
ETR  
ETS  
BUF  
INPUT MUX  
CHOPPER  
SOIC16 package  
DSP  
CONTROLLER  
FILTER  
INT. CLOCK  
TIMER  
CLK  
VBAT  
RSHH  
Self- and system-calibration  
with auto-calibration on power up  
16 kHz maximum sampling frequency  
Internal temperature measurement  
Internal factory trimmed precision reference  
Programmable current sources  
Digital comparator  
Active wake-up  
PGA gains 1, 6, 24, 50, 100  
Zero offset  
Zero offset TC  
Extremely low noise  
Internal oscillator with comparator for active wake up  
3-wire serial interface, μP compatible  
Temperature range – 40 to + 125 °C  
Individual 24-bit serial number  
16 BIT - CONVERTER  
PROTECTION  
EZPRG  
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
PGA  
and  
LEVEL SHIFT  
COMPARATOR  
RSHL  
CURRENT  
SOURCES  
SERIAL INTERFACE / CONTROL REGISTERS  
SCLK  
SDAT  
INTN  
Figure 1: Functional Block Diagram  
the high internal chopping frequency the system is free of 1/f-noise down  
to DC.The 0-10 Hz noise is typical below 1 µV i.e. as good or better than  
any other available chopper amplifier.  
For high speed synchronous measurements the chip can run in an  
automatic switching mode between two input channels with pre-  
programmed parameter sets.  
The circuit has been optimised for the application in battery management  
systems in automotive systems. As a front end data acquisition system it  
allows an high quality measurement of current, voltage and temperature  
of the battery.  
2
Applications  
ƒ
ƒ
ƒ
ƒ
Battery management for automotive systems  
Power management  
mV/µV-meter  
High-precision voltage and current measurement  
3
General description  
With a high quality 100 μΩ resistor the system can handle the starter  
current of up to 1500 A, a continuous current of ± 300 A as well as the  
very low idle current of a few mA in the standby mode.  
For external temperature measurement the chip can use a wide variety of  
different temperature sensors such as RTD, PTC, NTC, thermocouples or  
even diodes or transistors. A built-in programmable current source can be  
switched to any input and activate these sensors without the need of  
other external components.  
The AS8501 is a complete, low power data acquisition system  
for very small signals (i.e. voltages from shunt resistors,  
thermocouples) that operates on a single 5 V power supply. The  
chip powers up with a set of default conditions at which time it  
can be operated as a read-only-converter. Reprogramming is at  
any time possible by just writing into two internal registers via  
the serial interface.  
The measurement of the chip temperature with the integrated internal  
temperature sensor allows in addition the temperature compensation of  
sensitive parameters which increases the total accuracy considerably.  
The AS8501 has four ground refering inputs which can be  
switched separately to the internal PGA. Two input channels can  
also be operated as a fully differential ground free input. The  
system can measure both positive and negative input signals.  
Sensor specific data can be stored in the internal Zener-Zap memory and  
are used to calibrate each measurement in the internal data processing  
unit before transmission to the external µC via the serial SDI interface.  
The flexibility of the system is further increased by a digital comparator  
that can be assigned to any measured property  
The PGA amplification ranges from 6 to 100 which enables the  
system to measure signals from 7mV to 120 mV full scale range  
with high accuracy, linearity and speed.  
The chip contains a high precision bandgap reference and an  
active offset compensation that makes the system offset free  
(better than 0,5 μV) and the offset-TC value negligible. The built-  
in programmable digital filter allows an effective noise  
(current, voltage, temperature) and an active wake-up in the sleep-mode.  
All analog input-terminals can be checked for wire break via the SDI-  
interface.  
suppression if the high speed is not necessary in the application.  
The input noise density is only 35 nV /  
and due to  
Hz  
Revision 1.1, 04-April-06  
www.austriamicrosystems.com  
Page 1 of 40  

与AS8501相关器件

型号 品牌 获取价格 描述 数据表
AS8501_06 AMSCO

获取价格

High precision voltage and current measurement sensor interface
AS8501T&R AMSCO

获取价格

High precision voltage and current measurement sensor interface
AS8501TR AMSCO

获取价格

High precision voltage and current measurement sensor interface
AS8501TUB AMSCO

获取价格

High precision voltage and current measurement sensor interface
AS85049-32-1 GLENAIR

获取价格

90° Adapter, Non-Environmental, RFI
AS8506 AMSCO

获取价格

Battery Cell Monitor and Balancer IC
AS8506-BQFM AMSCO

获取价格

Battery Cell Monitor and Balancer IC
AS8506-BQFP AMSCO

获取价格

Battery Cell Monitor and Balancer IC
AS8506C-BQFM AMSCO

获取价格

Battery Cell Monitor and Balancer IC
AS8506C-BQFP AMSCO

获取价格

Battery Cell Monitor and Balancer IC