CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Surface Mount
@Super low ESR, impedance and high heat resistance have been obtained by using con-
ductive polymer as electrolyte.
@Suitable for DC-DC converters, voltage regulators and decoupling applications.
@Endurance with ripple current : 125C 1000 hours
@Rated voltage range : 2.5 to 20Vdc, Capacitance range : 22 to 1000MF
@Case size range : F6.3B5.7L to F10B7.7L
@Pb-free design
SPECIFICATIONS
?
Items
Characteristics
Category
Temperature Range
-55 to +125C
Rated Voltage Range 2.5 to 20Vdc
Capacitance Tolerance P20% (M)
(at 20C, 120Hz)
(at 105C)
Surge Voltage
Rated voltageB1.15V
Leakage Current
Shall not exceed value shown in STANDARD RATINGS.
(at 20C after 2 minutes)
Dissipation Factor
(tane)
0.12 max.
(at 20C, 120Hz)
Low Temperature
Characteristics
Z(
-
25C)/Z(+20C)[1.15
(Max. Impedance Ratio) Z(
-55C)/Z(+20C)[1.25
(at 100kHz)
Endurance
The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 1000 hours
at 125C.
Appearance
Capacitance change
DF (tanE)
No significant damage
[P20% of the initial value
[200% of the initial specified value
[200% of the initial specified value
[The initial specified value
ESR
Leakage current
Bias Humidity
Surge Voltage
Failure Rate
The following specifications shall be satisfied when the capacitors are restored to 20C after subjecting them to the DC rated voltage at
60C, 90 to 95% RH for 1000 hours.
Appearance
Capacitance change
DF (tanE)
No significant damage
[P20% of the initial value
[150% of the initial specified value
[150% of the initial specified value
[The initial specified value
ESR
Leakage current
The capacitors shall be subjected to 1000 cycles each consisting of charge with the surge voltage specified at 105C for 30 seconds
through a protective resistor(R=1kO) and discharge for 5 minutes 30 seconds.
Appearance
Capacitance change
DF (tanE)
No significant damage
[P20% of the initial value
[150% of the initial specified value
[150% of the initial specified value
[The initial specified value
ESR
Leakage current
1% per 1000 hours maximum (Confidence level 60%)
*Note : If any doubt arises, measure the leakage current after following voltage treatment.
Voltage treatment : DC rated voltage are applied to the capacitors for 120 minutes at 125C.
DIMENSIONS [mm]
MARKING
?
?
EX) PXH20VC22MF60
@Terminal Code : A
W
H
39F
22
Size code fD
L
A
B
C
W
P
20V
F60
H70
J80
6.3 5.7 6.6 6.6 7.2 0.5 to 0.8 1.9
6.7 8.3 8.3 9.0 0.7 to 1.1 3.1
10 7.7 10.3 10.3 11.0 0.7 to 1.1 4.5
8
0.3max.
AP0.2
LP0.3
PART NUMBERING SYSTEM
?
1
2
3
4
5
6
7
8
9
10
11 12 13
14
15 16 17
18
A P X H A A A A R A A A A M A A A G
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 10MF:100,100MF:101)
Taping code
Terminal code
Voltage code (ex. 6.3V:6R3,10V:100)
Series code
Category
Please refer to "A guide to global code (conductive polymer type)"
(1/2)
CAT. No. E1001E