5秒后页面跳转
ADIN1200 PDF预览

ADIN1200

更新时间: 2024-11-19 14:57:59
品牌 Logo 应用领域
亚德诺 - ADI 以太网
页数 文件大小 规格书
87页 1754K
描述
可靠的工业低功耗 10 Mbps 和 100 Mbps 以太网 PHY

ADIN1200 数据手册

 浏览型号ADIN1200的Datasheet PDF文件第2页浏览型号ADIN1200的Datasheet PDF文件第3页浏览型号ADIN1200的Datasheet PDF文件第4页浏览型号ADIN1200的Datasheet PDF文件第5页浏览型号ADIN1200的Datasheet PDF文件第6页浏览型号ADIN1200的Datasheet PDF文件第7页 
Data Sheet  
ADIN1200  
Robust, Industrial, Low Power, 10 Mbps and 100 Mbps Ethernet PHY  
Test and measurement  
FEATURES  
Industrial internet of things (IoT)  
10BASE-Te/100BASE-TX IEEE 802.3TM compliant  
MII, RMII and RGMII MAC interfaces  
®
GENERAL DESCRIPTION  
100BASE-TX RGMII latency transmit: <124 ns, receive <250 ns  
100BASE-TX MII latency transmit: <52 ns, receive <248 ns  
Programmable RGMII timing delay and drive current  
Supports TSN  
EMC test standards  
IEC 61000-4-5 surge (±4 kV)  
IEC 61000-4-4 electrical fast transient (EFT) (±4 kV)  
IEC 61000-4-6 conducted immunity (10 V)  
EN55032 radiated emissions (Class A)  
EN55032 conducted emissions (Class A)  
Unmanaged configuration using multilevel pin strapping  
MDIO/MDC management interface and interrupt pin  
EEE in accordance with IEEE 802.3az  
Start of packet detection for IEEE 1588 time stamp support  
Enhanced link detection  
Cable diagnostics (TDR and signal analysis)  
Configurable LED  
Crystal oscillator/clock input: 25 MHz  
25 MHz/125 MHz synchronous clock output  
Jumbo frame support up to 16 kBytes  
Synchronous Ethernet (SyncE) clock recovery  
32-lead, 5 mm × 5 mm LFCSP small package  
The ADIN1200 is a low power, single-port, 10 Mbps and 100 Mbps  
Ethernet transceiver with low latency specifications designed for  
industrial Ethernet applications.  
This design integrates an energy efficient Ethernet (EEE) physical  
layer device (PHY) core with all associated common analog circui-  
try, input and output clock buffering, management interface and  
subsystem registers, and media access control (MAC) interface and  
control logic to manage the reset, clock control and pin configura-  
tion.  
The ADIN1200 is available in a 5 mm × 5 mm, 32-lead lead frame  
chip scale package (LFCSP) and can operate with a single 3.3  
V supply, assuming the use of a 3.3 V MAC interface supply.  
For maximum flexibility in system level design, a separate VDDIO  
supply enables the management data input/output (MDIO) and  
MAC interface supply voltages to be configured independently of  
the other circuitry on the ADIN1200 allowing operation at 1.8 V, 2.5  
V, or 3.3 V. At power-up, the ADIN1200 is held in hardware reset  
until each of the supplies has crossed its minimum rising threshold  
value and the power is considered good. Brownout protection is  
provided by monitoring the supplies to detect if one or more of them  
drops below a minimum falling threshold and holding the device  
in hardware reset until the power supplies return and satisfy the  
power-on-reset (POR) circuit.  
The MII management interface (also referred to as MDIO interface)  
provides a 2-wire serial interface between a host processor or  
MAC and the ADIN1200, allowing access to control and status  
information in the PHY core management registers. The interface  
Wide temperature range: specified for −40°C to +105°C and  
−40°C to +85°C ambient operation  
Low power consumption  
®
139 mW for 100BASE-TX  
is compatible with both IEEE 802.3 Standard Clause 22 and  
Clause 45 management frame structures.  
3.3 V/2.5 V/1.8 V MAC interface VDDIO supply  
Single-supply operation with 3.3 V VDDIO  
Integrated power supply monitoring and POR  
The ADIN1200 can support cable lengths up to 180 meters.  
Note that throughout this data sheet, multifunction pins, such as  
XTAL_I/CLK_IN/REF_CLK, are referred to either by the entire pin  
name or by a single function of the pin, for example, XTAL_I, when  
only that function is relevant.  
APPLICATIONS  
Industrial automation  
Process control  
Factory automation  
Table 1. Related Products  
Product No.  
Description  
Robotics and motion control  
Time sensitive networking (TSN)  
Building automation  
ADIN1300  
Robust, industrial, low latency gigabit Ethernet PHY in  
40-lead (6 mm × 6 mm) LFCSP  
Analog Devices is in the process of updating documentation to provide terminology and language that is culturally appropriate. This is a process  
with a wide scope and will be phased in as quickly as possible. Thank you for your patience.  
Rev. A  
Information furnished by Analog Devices is believed to be accurate and reliable "as is". However, no responsibility is assumed by Analog  
Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to  
DOCUMENT FEEDBACK  
change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and  
registered trademarks are the property of their respective owners.  
TECHNICAL SUPPORT  

与ADIN1200相关器件

型号 品牌 获取价格 描述 数据表
ADIN1300 ADI

获取价格

鲁棒的工业、低延迟和低功耗10 Mbps、100 Mbps和1 Gbps以太网PHY
ADIN2111 ADI

获取价格

集成10BASE-T1L PHY的低复杂度、2端口以太网交换机
ADIN2299 ADI

获取价格

RapID平台第2代(RPG2)网络接口
A-DIO-DP-04 ASSMANN

获取价格

ASS 1067A CO
A-DIO-DP-06 ASSMANN

获取价格

ASS 1067 CO
A-DIO-DP-08 ASSMANN

获取价格

ASS 1067A CO
ADIP 08Z-LC ASSMANN

获取价格

CONN DIP IDC 8POS TIN
ADIP 10Z-LC ASSMANN

获取价格

CONN DIP IDC 10POS TIN
ADIP 14Z-LC ASSMANN

获取价格

CONN DIP IDC 14POS TIN
ADIP 16Z-LC ASSMANN

获取价格

CONN DIP IDC 16POS TIN