Data Sheet
AD9670
Addr.
(Hex)
Default
Bit 0 (LSB) Value
Register Name
Bit 7 (MSB) Bit 6
X X
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Comments
0x109 VGA_TEST
X
VGA/ anti-
aliasing
filter test
mode
enable
0 = off
X
VGA/ antialiasing filter output test mode 0x00
000 = Channel A (default)
001 = Channel B
VGA/ antialiasing
filter test mode
enables antialiasing
filter output to the
GPO2 and GPO3
pins (global).
010 = Channel C
011 = Channel D
100 = Channel E
(default)
1 = on
101 = Channel F
110 = Channel G
111 = Channel H
0x10C PROFILE_INDEX
X
X
Manual
TX_TRIG
0 = off,
use pin
(default)
1 = on,
Profile Index[4:0]
0x00
Index for profile
memory selects
active profile
(global).
auto-
generate
TX_TRIG
(self clears)
0x10D RESERVED_10D
0x10E RESERVED_10E
0x10F DIG_OFFSET_CAL
1
1
0
1
1
0
1
1
0
1
1
0
1
1
1
1
1
1
1
0xFF
0xFF
Reserved.
Reserved.
1
Digital
offset
Digital offset calibration
000 = disable correction, reset
correction value (default)
001 = average 210 samples
010 = average 211 samples
…
Controls digital
offset calibration
enable and the
number of samples
used (global).
calibration
status
0 = not
complete
(default)
1 =
111 = average 216 samples
complete
0x110 DIG_OFFSET_
CORR1
D7
D6
D5
D4
D3
D2
D1
D9
D0
D8
0x00
0x00
Offset correction
LSB (local, chip).
0x111 DIG_OFFSET_
CORR2
D15
D14
D13
D12
D11
D10
Offset correction
MSB (local, chip).
Digital offset calibration (read back if auto calibration is enabled with Register 0x10F; otherwise,
force correction value
Offset correction = [D15:D0] × AFULL SCALE/216
0111 1111 1111 1111 (215 − 1) = +1/2 × AFULL SCALE − 1/216 × AFULL SCALE
0111 1111 1111 1110 (215 − 2) = +1/2 × AFULL SCALE − 2/216 × AFULL SCALE
…
0000 0000 0000 0001 (+1) = 1/216 × AFULL SCALE
0000 0000 0000 0000 = no correction (default)
1111 1111 1111 1111 (−1) = −1/216 × AFULL SCALE
…
1000 0000 0000 0000 (−215) = −1/2 full scale
0x112 POWER_MASK_
CONFIG
X
X
X
X
X
Power up set-up time (POWER_SETUP)
0 0000 = 0
0x02
0x00
Power setup time
is used to set the
power-up time
(global).
0 0001 = 1 × 40/fSAMPLE
0 0010 = 2 × 40/fSAMPLE (default)
0 0011 = 3 × 40/fSAMPLE
…
1 1111 = 31 × 40/fSAMPLE
0x113 DIG_DEMOD_
CONFIG
Digital
high-pass
filter
0 = enable gain
(default)
Decimator
gain scale
0 = no
Decimator and filter
enable
Baseband Demod-
decimator ulator
Enable stages of
the digital
processing
(global).
00 = RF 2× decimator
bypassed (default)
01 = RF 2× decimator
enabled and low band
filter
0 = enable 0 = enable
(default)
1 = bypass 1 = bypass
(default)
(default)
1 = bypass 1 = 4×
gain (shift
decimator
1X = RF 2× decimator
output by enabled and high band
2) filter
0x115 CHIP_ADDR_EN
X
X
Chip
address
mode
Chip address qualifier
0 0000 (default)
(If read, returns the state of ADDR0 to ADDR4 pins)
0x00
Chip address
mode enables the
addressing of
0 = disable
(default)
1 = enable
devices if the value
of the chip address
qualifier equals the
state on the ADDR0
to ADDR4 pins
(global).
Rev. A | Page 47 of 52