Quad, 15 V, 256-Position, Digital
Potentiometer with Pin-Selectable SPI/I2C
Data Sheet
AD5263
FEATURES
FUNCTIONAL BLOCK DIAGRAM
A1
W1
B1 A2
W2
B2
W4
B4
A3
W3
B3 A4
256-position, 4-channel
V
DD
End-to-end resistance 20 kΩ, 50 kΩ, 200 kΩ
Pin-selectable SPI®- or I2C®-compatible interface
Power-on preset to midscale
V
SS
SHDN
RDAC 1
REGISTER
RDAC 2
REGISTER
RDAC 3
REGISTER
RDAC 4
REGISTER
RES/AD1
Two package address decode pins AD0 and AD1
Rheostat mode temperature coefficient 30 ppm/°C
Voltage divider temperature coefficient 5 ppm/°C
Wide operating temperature range –40°C to +125°C
10 V to 15 V single supply; 5 V dual supply
8
V
L
AD5263
CLK/SCL
SDI/SDA
CS/AD0
ADDRESS
DECODER
SERIAL INPUT
REGISTER
2
SPI/I C
SELECT
LOGIC
GND
APPLICATIONS
Mechanical potentiometer replacement
Optical network adjustment
DIS
NC/O2 SDO/O1
Figure 1.
Instrumentation: gain, offset adjustment
Stereo channel audio level control
Automotive electronics adjustment
Programmable power supply
Programmable filters, delays, time constants
Line impedance matching
Low resolution DAC/trimmer replacement
Base station power amp biasing
Sensor calibration
GENERAL DESCRIPTION
Wiper position programming presets to midscale upon power-
on. Once powered, the VR wiper position is programmed by
either the 3-wire SPI or 2-wire I2C-compatible interface. In the
I2C mode, additional programmable logic outputs enable users
to drive digital loads, logic gates, and analog switches in their
systems.
The AD5263 is the industry’s first quad-channel, 256-position,
digital potentiometer1 with a selectable digital interface. This
device performs the same electronic adjustment function as
mechanical potentiometers or variable resistors, with enhanced
resolution, solid-state reliability, and superior low temperature
coefficient performance.
The AD5263 is available in a narrow body, 24-lead TSSOP.
All parts are guaranteed to operate over the automotive
temperature range of –40°C to +125°C.
Each channel of the AD5263 offers a completely programmable
value of resistance between the A terminal and the wiper or
between the B terminal and the wiper. The fixed A-to-B
terminal resistance of 20 kΩ, 50 kΩ, or 200 kΩ has a nominal
temperature coefficient of 30 ppm/°C and a 1% channel-to-
channel matching tolerance. Another key feature of this part is
the ability to operate from +4.5 V to +15 V, or at 5 V.
For single- or dual-channel applications, refer to the
AD5260/AD5280 or AD5262/AD5282 data sheets.
1 The terms digital potentiometer, VR, and RDAC are used interchangeably.
Rev. F
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result fromits use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks andregisteredtrademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2003–2012 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com