IDT71V3556S/XS
IDT71V3558S/XS
IDT71V3556SA/XSA
128K x 36, 256K x 18
3.3V Synchronous ZBT SRAMs
3.3V I/O, Burst Counter
Pipelined Outputs
IDT71V3558SA/XSA
Description
Features
◆
TheIDT71V3556/58are3.3Vhigh-speed4,718,592-bit(4.5Mega-
bit) synchronous SRAMS. They are designed to eliminate dead bus
cycles when turning the bus around between reads and writes, or
writes and reads. Thus, they have been given the name ZBTTM, or
Zero Bus Turnaround.
128K x 36, 256K x 18 memory configurations
◆
Supports high performance system speed - 200 MHz (x18)
(3.2 ns Clock-to-Data Access)
Supports high performance system speed - 166 MHz (x36)
◆
(3.5 ns Clock-to-Data Access)
ZBTTM Feature - No dead cycles between write and read
◆
Address and control signals are applied to the SRAM during one
clock cycle, and two cycles later the associated data cycle occurs, be
it read or write.
cycles
◆
Internally synchronized output buffer enable eliminates the
The IDT71V3556/58 contain data I/O, address and control signal
registers. Output enable is the only asynchronous signal and can be
used to disable the outputs at any given time.
need to control OE
Single R/W (READ/WRITE) control pin
Positive clock-edge triggered address, data, and control
◆
◆
A Clock Enable (CEN) pin allows operation of the IDT71V3556/58
to be suspended as long as necessary. All synchronous inputs are
ignored when (CEN) is high and the internal device registers will hold
their previous values.
There are three chip enable pins (CE1, CE2, CE2) that allow the
user to deselect the device when desired. If any one of these three are
not asserted when ADV/LD is low, no new memory operation can be
initiated. However, any pending data transfers (reads or writes) will be
completed.Thedatabuswilltri-statetwocyclesafterchipisdeselected
orawriteisinitiated.
signal registers for fully pipelined applications
4-word burst capability (interleaved or linear)
Individual byte write (BW1 - BW4) control (May tie active)
Three chip enables for simple depth expansion
3.3V power supply (±5%), 3.3V I/O Supply (VDDQ)
Optional- Boundary Scan JTAG Interface (IEEE 1149.1
compliant)
Packaged in a JEDEC standard 100-pin plastic thin quad
flatpack (TQFP), 119 ball grid array (BGA) and 165 fine pitch
ball grid array (fBGA)
◆
◆
◆
◆
◆
◆
Pin Description Summary
A
0
-A17
Address Inputs
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Output
Input
Input
I/O
Synchronous
Synchronous
Asynchronous
Synchronous
Synchronous
Synchronous
N/A
Chip Enables
CE
1
, CE
2
, CE
2
Output Enable
OE
R/W
Read/Write Signal
Clock Enable
CEN
Individual Byte Write Selects
Clock
BW
1
, BW
2
, BW
3
, BW
4
CLK
ADV/LD
LBO
Advance burst address / Load new address
Linear / Interleaved Burst Order
Test Mode Select
Test Data Input
Synchronous
Static
TMS
TDI
Synchronous
Synchronous
N/A
TCK
Test Clock
TDO
Test Data Output
Synchronous
Asynchronous
Synchronous
Synchronous
Static
JTAG Reset (Optional)
Sleep Mode
TRST
ZZ
I/O
0
-I/O31, I/OP1-I/OP4
Data Input / Output
Core Power, I/O Power
Ground
V
V
DD, VDDQ
SS
Supply
Supply
Static
5281 tbl 01
OCTOBER 2010
1
DSC-5281/11
©
2010 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice.