60DDW4_3 Series
60W - Single/Dual Output - Wide Input - Isolated & Regulated
DIP DC-DC Converter
DC-DC Converter
60 Watt
The 60DDW series offers 60W of output, wide input voltage of
9-36VDC, 18-72VDC and features 3000VDC isolation, six-sided metal
shield over current and short circuit protection.
High efficiency up to 88%
4:1 wide input voltage range
Isolation voltage 3000VDC
Six-sided metal shield
Short circuit protection (SCP)
(automatic recovery)
Operating temperature:
-40°C to +85°C
Over temperature protection
Industry standard pinout
Under voltage lockout
All models are particularly suited to tele-communications, industrial,
test equipments power etc.
Common specifications
Cooling:
Output specifications
Free air convection
Item
Test condition
Single/dual
Min Typ
120 150
Max
2
Units
ꢀ
Short circuit protection:
Operation temperature range:
Storage temperature range:
Case temperature:
Continuous, auto-recovery
-40°C~+85°C
Voltage tolerance
Over load
protection
Input voltage range
180
ꢀ
-55°C~+100°C
Line regulation
Single & Dual
(H/L to L/L%
0.5
0.5
ꢀ
ꢀ
90°C MAX
Lead temperature range:
Switching frequency (PWM mode%:
Humidity:
265°C MAX, 1.5mm from case for 10 sec
50kHz TYP
Load regulation
Single & Dual
(F.L-50ꢀF.L%
Minimum load
30ꢀ of full load
non-condensing, 95ꢀ MAX
Six-Side Shielded Case
Epoxy (UL94V-0 rated%
EN55022, Class A
EN55022, Class A
>299,424 hours
Ripple and noise*
20MHz Bandwidth
100
150
400
mVp-p
µs
Case material:
Transient response 50ꢀ load step change
setting time
Potting material:
Radiated Emissions:
Conducted Emissions:
MTBF (MIL-HDBK-217F @25°C%*:
Weight:
Capacitive load
1500 µF
External Trim Adj.
Range
10ꢀ of Output
Voltage
227.5g
* Test ripple and noise by “parallel cable” method. Typical value at nominal input
voltage and no load.
Input specifications
Model selection:
WCTV_xxyyN##
Item
Test condition
Pi network
Min
Typ
Max
Units
W= Watt; C=Case; T= Type; V= Voltage Variation (omitted 10ꢀ%;
xx= Vin; yy= Vout; N= Numbers of Output; ##= Isolation (kVDC%
Filter
Protection
Fuse recommended
Example:
60DDW_2415S3
60= 60Watt; D= DIP; D= series; W4= wide input (4:1) 9-36Vin;
15Vout; S= single output; 3= 3000VDC
Isolation specifications
Item
Test condition
Min
Typ
Max
Units
VDC
Isolation voltage
Input/Output, tested
for 1 minute
3000
Note:
1. Input voltage can’t exceed this value, or will cause the permanent damage.
2. The load shouldn‘t be less than 5ꢀ, otherwise ripple will increase dramatically.
3. Max. Capacitive Load is tested on Vin-nominal and full load.
4. All specifications measured at Ta=25°C, humidity<75ꢀ, nominal input voltage
and rated output load unless otherwise specified.
Isolation resistance
Isolation capacitance
500VDC
1000
MΩ
Input/Output
2500
pF
5. In this datasheet, all the test methods of indications are based on corporate
standards.
6. Only typical models listed, other models may be different, please contact our
technical person for more details.
7. Specifications subject to change without notice.
Page 1 of 3
60DDW4_3 – Rev. 2016-1.0
Specifications subject to change without notice.
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com