60DAW4_1.6 Series
60W - Single/Dual Output - Wide Input - Isolated & Regulated
DIP DC-DC Converter
DC-DC Converter
60 Watt
The 60DAW4_1.6 series offers 60W of output, wide input voltage of
9-36VDC, 18-75VDC and features 1600VDC isolation, six-sided metal
shield over current and short circuit protection.
High efficiency up to 93%
4:1 wide input voltage range
Isolation voltage 1600VDC
Six-sided metal shield
Short circuit protection (SCP)
(automatic recovery)
Operating temperature:
-40°C to +85°C
Over temperature protection
Industry standard pinout
Under voltage lockout
All models are particularly suited to industry control systems, semicon-
ductor equipment, wireless network, telecom/datacom, measurement
etc.
Common specifications
Cooling:
Output specifications
Nature convection
Item
Test condition
Min Typ
Max
1
Units
ꢀ
Short circuit protection:
Operation temperature range:
Storage temperature range:
Case temperature:
Continuous, auto-recovery
-40°C~+100°C
Voltage accuracy
External trim adj.
range
of output
10
ꢀ
-55°C~+125°C
Over load
protection
Input voltage range
150
ꢀIo
110°C
Lead temperature range:
260°C MAX, 1.5mm from case for 10 sec
Line regulation
0.5
ꢀ
Thermal impedance:
(Mounting at FR4 (5.9*2.75inch% PCB%
without heatsink: 9.5°C/W, min.
with heatsink: 8.5°C/W, min.
Load regulation
(0ꢀ-100ꢀ%
• Single
• Dual
0.5
1
ꢀ
ꢀ
Switching frequency:
Humidity:
225kHz TYP
Cross regulation
Ripple and noise
Dual, 25ꢀ-100ꢀ load
5
ꢀ
non-condensing, 5ꢀ-95ꢀ MAX
Copper
20MHz Bandwidth, 1.0µF
ceramic capacitor
100
mVpk-pk
Case material:
Over voltage
protection
(Zener diode
clamp%
• 5VDC
• 12VDC
• 15VDC
6.2
15
20
V
V
V
Potting material:
Design meets safety:
MTBF (MIL-HDBK-217F @25°C%:
Weight:
Epoxy (UL94V-0 rated%
IEC60950-1/EN60950-1
>210,000 hours
45g
Over load
protection
of Iout
120~
140
ꢀ
Temperature
coefficient
0.02
ꢀ/°C
µs
Input specifications
Transient recovery 25ꢀ load step change
time
250
Item
Test condition
Min
Typ
Max
Units
Transient response 25ꢀ load step change
deviation
3
ꢀ
Under voltage lockout • 24Vin
8.6/7.9
17.8/16
VDC
VDC
Module ON/OFF
Start-Up time1%
Filter
• 48Vin
60
mS
Isolation specifications
Pi type
Item
Test condition
for 10 seconds
Test at 500VDC
Min
Typ
Max
Units
VDC
MΩ
pF
Input reflected ripple
current2%
Nominal Vin
and full load
20
mAp-p
Isolation voltage
Isolation resistance
Isolation capacitance
1600
Remote ON/OFF3%
• ON
• OFF
• Off idle current
3.0 ... 12VDC or open circuit
0 ... 1.2VDC or Short circuit pins 2, 3
mA
1000
5
2200
1% Nominal Vin and constant resistive load
2% Measured with a simulated source inductance of 1µH
3% The ON/OFF control pin is referenced to -Vin (pin2%.
Note:
Model selection:
1. Input voltage can’t exceed this value, or will cause the permanent damage.
2. The load shouldn‘t be less than 5ꢀ, otherwise ripple will increase dramatically.
3. Max. Capacitive Load is tested on Vin-nominal and full load.
4. All specifications measured at Ta=25°C, humidity<75ꢀ, nominal input voltage
and rated output load unless otherwise specified.
5. In this datasheet, all the test methods of indications are based on corporate
standards.
6. Only typical models listed, other models may be different, please contact our
technical person for more details.
WCTV_xxyyN##
W= Watt; C=Case; T= Type; V= Voltage Variation (omitted 10ꢀ%;
xx= Vin; yy= Vout; N= Numbers of Output; ##= Isolation (kVDC%
Example:
60DAW4_2415S1.6
60= 60Watt; D= DIP; A= series; W4= wide input (4:1) 9-36Vin;
15Vout; S= single output; 1.6= 1600VDC
7. Specifications subject to change without notice.
Page 1 of 5
60DAW4_1.6 – Rev. 2017-1.0
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
Specifications subject to change without notice.