600ACP_SCF Series
600W - Single Output AC-DC Converter - Universal Input - Isolated & Regulated
AC-DC Converter
600 Watt
High efficiency up to 93.8%
Universal AC input range
(85~264VAC)
Short circuit protection (SCP)
Wide operating ambient
temperature (-20°C~70°C)
Operating altitude up to
5000M
100% full load burn-in test
PCB soldering side with
conformal coating
The 600ACP_SCF series features standard rail mounting, energy efficien-
cy and is highly cost-effective. The series offers stability and high noise
immunity especially for industrial control equipment, machinery and
other demanding environments for industrial equipment. This converter
offers a compact and light weight design with and standard rail installati-
on (35mm). Furthermore this series offers Easy Fuse Tripping due and a
built-in DC OK relay contact. The converter can be installed on TS-35/7.5
or TS-35/15.
Built-in Active PFC function,
PF>0.95
Short circuit protection (SCP)
Over voltage protection (OVP)
Over load protection (OLP)
UL-60950-1 (E347551)
Common specifications
Short circut protection:
Temperature rise at full load:
Cooling method*:
Input specifications
Long-term mode, automatic recovery
Input voltage range
Input frequency
Power factor
90~264VAC
47~63Hz
40°C MAX
Fan
12V only
115VAC
0.98 (typ)
230VAC
@230VAC
0.95 (typ)
Operation temperature range:
Storage temperature range:
Storage humidity range:
Temperature coefficient:
MTBF (using MIL-HDBK-217F):
Power boost:
-20°C~+70°C
AC current
• 12V
• 24V/48V
5A (max)
6A (max)
-40°C ~+85°C
10%~95%, no condensing
0.03%/°C MAX
Inrush current
Cold start
• 12V
• 24V/48V
115VAC
220VAC
40A (typ)
30A (typ)
15A (typ)
+25°C >200,000 hours
150% of rated current
support
UL60950-1 2nd Ed; IEC 60950-1:2005 (2nd
Ed); EN60950-1:2006
Leakage current
Input—output: ≤0.25mA
Input—PG: ≤3.5mA (264Vac, 63Hz)
Parallel function:
Standy power
consumption
<5W
Safety standards:
Output specifications
Case material:
Heat-resistant Plastic (UL94-V0) and
metal
Item
Test conditions
Min Typ
Max
Units
Output voltage
accuracy
Full load
• 12V
• 24V/48V
Dimensions:
Weight:
218*116.5*40.7mm
1333.33g
3
2
%
%
Line regulation
Load regulation
Set-up time
• 12V
1
%
%
12V
• 24V/48V
0.5
Fan working: temperature ctrl. up to 55 10°C or output current >17-22A
Fan stop working: temperature ctrl. down to 40 10°C or output current<15-20A
24V/48V
• 12V
• 24V/48V
2
1
%
%
Fan working: temperature ctrl. up to 55 10°C or output current > 40%~60% of rated current
Fan stop working: temperature ctrl. down to 40 10°C or output current<30%~50% of rated current
• 12V @220VAC input
• 24V/48V @220VAC
input
• 24V/48V @110VAC
input
2
s
s
1.5
Isolation specifications
2.5
s
Item
Test condition
Min
Typ
Max
Units
VAC
Withstand voltage*
• Primary-Sec.: 10mA
• Primary-PG: 10mA
• Secondary-PG
3000
1500
500
Hold-up time
220VAC @full load
10
ms
%
Overshoot and
undershoot
5
Isolation resistance
10
MΩ
Switching frequency
100
KHz
* Input-Output, tested for 1 minute, 500VDC and leakage current less than 1mA
* Measured at 20MHz of bandwidth by using a 12” twisted pair-wire terminated
with a 0.1 uF & 10uF parallel capacitor.
Protection specifications
Over-load
protection
12V: 52.5~65A; 24V/48V: 26.25~32.5A
Protection type:
Example:
600ACP_24SCF
600 = 600Watt
AC = AC-DC
12V: Intermittent working, working time>0.1s, recovery
time >2s
24V/48V: Hiccup mode, auto recovery
P = series
24 = 24 Vout
S = Single Output
C = PFC (Power Factor Correction)
F = Fan
Over-voltage
protection
12V: 13.6~16V; 24V: 28~32V; 48V: 54~60W
Protection type:
Constant voltage, auto recovery
Over-temperature
protection
95°C+5°C (detect on thermal protector on PFC mosfet);
shut down,auto recovery after the temperature goes
down to 40°C
Note:
1. All parameters NOT specially mentioned are measured at rated input, rated
load and 25°C of ambient temperature.
Page 1 of 3
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
600ACP_SCF – Rev. 2020-1.0
Specifications subject to change without notice.