5P49V5901 DATASHEET
OTP Interface
Table 5: SD/OE Pin Function Truth Table
The 5P49V5901 can also store its configuration in an internal
OTP. The contents of the device's internal programming
registers can be saved to the OTP by setting burn_start
(W114[3]) to high and can be loaded back to the internal
programming registers by setting usr_rd_start(W114[0]) to
high.
SH bit SP bit OSn bit OEn bit SD/OE
OUTn
0
0
0
0
0
0
0
0
0
1
1
1
x
0
1
1
x
x
0
1
Tri-state2
Output active
Output active
Output driven High Low
0
0
0
0
1
1
1
1
0
1
1
1
x
0
1
1
x
x
0
1
Tri-state2
Output active
Output driven High Low
Output active
2
To initiate a save or restore using I C, only two bytes are
transferred. The Device Address is issued with the read/write
bit set to “0”, followed by the appropriate command code. The
save or restore instruction executes after the STOP condition
is issued by the Master, during which time the 5P49V5901 will
not generate Acknowledge bits. The 5P49V5901 will
1
1
1
0
0
0
0
1
1
x
0
1
0
0
0
Tri-state2
Output active
Output active
1
1
1
1
1
1
0
1
1
x
0
1
0
0
0
Tri-state2
acknowledge the instructions after it has completed execution
Output active
Output driven High Low
Output driven High Low 1
2
of them. During that time, the I C bus should be interpreted as
busy by all other users of the bus.
1
x
x
x
1
On power-up of the 5P49V5901, an automatic restore is
performed to load the OTP contents into the internal
programming registers. The 5P49V5901 will be ready to
accept a programming instruction once it acknowledges its
Note 1 : Global Shutdown
Note 2 : Tri-state regardless of OEn bits
2
Output Divides
7-bit I C address.
2
Each output divide block has a synchronizing POR pulse to
provide startup alignment between outputs divides. This
allows alignment of outputs for low skew performance. This
low skew would also be realized between outputs that are
both integer divides from the VCO frequency. This phase
alignment works when using configuration with SEL1, SEL0.
Availability of Primary and Secondary I C addresses to allow
2
programming for multiple devices in a system. The I C slave
address can be changed from the default 0xD4 to 0xD0 by
programming the I2C_ADDR bit D0. VersaClock 5
2
Programming Guide provides detailed I C programming
guidelines and register map.
2
2
For I C programming, I C reset is required.
SD/OE Pin Function
An output divide bypass mode (divide by 1) will also be
provided, to allow multiple buffered reference outputs.
The polarity of the SD/OE signal pin can be programmed to be
either active HIGH or LOW with the SP bit (W16[1]). When SP
is “0” (default), the pin becomes active LOW and when SP is
“1”, the pin becomes active HIGH. The SD/OE pin can be
configured as either to shutdown the PLL or to enable/disable
the outputs. The SH bit controls the configuration of the
SD/OE pin The SH bit needs to be high for SD/OE pin to be
configured as SD.
Each of the four output divides are comprised of a 12 bit
integer counter, and a 24 bit fractional counter. The output
divide can operate in integer divide only mode for improved
performance, or utilize the fractional counters to generate a
clock frequency accurate to 50 ppb.
Each of the output divides also have structures capable of
independently generating spread spectrum modulation on the
frequency output.
SP
OUTn
SD/OE Input
The Output Divide also has the capability to apply a spread
modulation to the output frequency. Independent of output
frequency, a triangle wave modulation between 30 and 63kHz
may be generated.
OEn
Global Shutdown
OSn
SH
For all outputs, there is a bypass mode, to allow the output to
behave as a buffered copy of the input.
When configured as SD, device is shut down, differential
outputs are driven High/low, and the single-ended LVCMOS
outputs are driven low. When configured as OE, and outputs
are disabled, the outputs are driven high/low.
PROGRAMMABLE CLOCK GENERATOR
8
NOVEMBER 11, 2016
5秒后页面跳转
SG3525资料手册详解：SG3525参数分析、引脚说明、应用介绍
AT89C51单片机资料手册详细解析及应用示例
CP2102资料手册解读：CP2102引脚说明、关键参数分析
资料手册解读：UC3842参数和管脚说明
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
