3 x 5mm Rectangular
®
Optopipe®
Optical Light Pipe, 2 Array (RJ45 Jack)
515-1070
19.05
FRONT
Recommended
MicroLED SMT LEDs
for use with 515-1070
[.750]
PANEL
13.98
[.550]
31.24
[1.23]
29.0
[1.142]
5.08
[.200]
2 PLCS
DIFFUSED
FRONT
SURFACE
2.54
[.100]
3.05
[.120]
20.57
[.81]
3.56
[.140]
1.91
[.075]
PART NO.
597-3001-1xx
597-3111-1xx
597-3111-5xx
597-3211-1xx
597-3211-5xx
597-3301-1xx
597-3301-5xx
597-3401-1xx
597-3401-5xx
597-7701-1xx
597-7701-5xx
597-7721-1xx
597-7721-5xx
597-7731-1xx
COLOR
Red
PAGE #
1-19
1-19
1-30
1-19
1-30
1-19
1-30
1-19
1-30
1-20
1-31
1-20
1-31
1-20
3.93
[.155]
C.L. LEDS
3.66
[.144]
7.62 .15
[.300 .006]
AlGaAs Red
AlGaAs Red
Orange
27.94
[1.100]
27.43
[1.080]
1.57
[.062]
35.26
[1.388]
C.L. MOUNTING
PIN #1
.71
1.50
[.059]
[.028]
Orange
.99
[.039]
2.01
[.079]
.99
[.039]
1.57
[.062]
Green
DIRECTINO
OF LIGHT
Green
NOTE: designed for
post-reflow
PC board insertion.
1.35
[.053]
13.98
[.550]
2XØ 2.87 .05
[.113 .002]
Yellow
6.99
[.275]
Yellow
27.94 .05
[1.100 .002]
Red/Green
Red/Green
Yellow/Green
Yellow/Green
Red/Yellow
Dimensions in mm [inches]
RECOMMENDED SOELRDPAD/HOLES LYAOUT
FOR BI-COLOR LSED
Features
• Complements Dialight’s 515-1022 Four Array Optopipe
Light Pipe
• Allows indicators to be positioned above corresponding
RJ45 jack or D-Subminiature
LED Data
For absolute maximum ratings and other electri-
cal and optical data on the recommended LEDs,
refer to LED data sheets.
• High transmissivity polycarbonate material
• UL94V-0 compliance
• ESD protection (circuit isolation from front panel)
• Wide viewing angle
Operating/Storage Temperature
• Arrays reduce insertion costs
–30°C to +100°C
• Secures to PCB by press-fit
Dialight Optopipe® Light Pipe Description
This light pipe’s two 3 x 5mm rectangular light emitting surfaces appear bright and are optically well isolated. The light
pipe is reliably held in place by 2 press-fit pins located at either end of the light pipe array. This Optopipe® functions as a
through-the-case indicator by conducting the light over the top of connectors or switches. A textured finish on the 2 light
emitting surfaces maximizes the viewing angle. The recommended light sources are Dialight's 597 Series PLCC-2 or
PLCC-4 Type SMT LEDs. The LEDs are mounted in a straight line on an 0.550" pitch. The light pipe material is water clear
transmissive polycarbonate rated UL94-V0, and has a 35% oxygen index.
Dialight can provide custom Optopipe® solutions for your applications.
Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com