Multi-Deck Rotary Switches
ACCESSORIES
.060 .002
(1,52 0,05)
.625 .010
(15,88 0,25)
ꢀIꢁ.
.376 + .003 –.000
(9,55 + 0,08 –0,00)
ꢀIꢁ.
bushing to the panel. The kit consists of four
items: a grooved hex nut, a keyed washer, a
keyed seal and a non-turn washer. ꢁssembly is
described on Page J-53. ꢀimensions of panel
seal kit items are shown in Figure C. This kit
seals the bushing to the panel; it does not seal
the shaft to the bushing. Not usable with
adjustable stop switches. Part No. 42-24
Internal Tooth Lockwasher–Figure A
For a 3/8" bushing. ꢁpproximately 0.500" (12,7)
outsidediameter,.022"(0,56)thickness.Material
is cadmium-plated steel. Part No. 12Q1272-1
For a 1/4" bushing. ꢁpproximately
.154
.032 .002
(0,81 0,05)
+ .004
–.000
(3,91
+ 0,10
–0,00)
ꢀIꢁ.
.437 .010
(11,10 0,25)
0.400" (10,16) outside diameter, .018"
(0,46) thickness. Material is steel, tin/
.125 .010
(3,18 0,25)
.120 .003
(3,18 0,08)
zinc plated.
FIGURE A
FIGURE B
Non-Turn Washer–Figure B
.625 .010
(15,88 0,25) ꢀIꢁ.
.045 .003
(1,14 0,08)
.010 .002
(0,25 0,05)
.562 (14,27)
ꢁCROSS
FLꢁTS
Can be ordered as extra hardware for the
Series5000, 24, 42, 43, 44, 54, 71B, 53, 57and
59 rotary switches. The internal key of the
washer slides into the bushing keyway. The
right angle tab locks into a predrilled hole on
the back side of the mounting panel. Material is
brass, tin/zinc plated. Part No. 12C1087-1
.032
.002
(0,81
0,05)
.375 + .004 – .000
(9,53 + 0,10) ꢀIꢁ.
.375 .005
(9,53 0,13)
C
L
.187 .010
(4,75 0,25)
.088 (2,24)/
.093 (2,36)
.125 .003
(3,18 0,08)
Panel Seal Kit–Figure C
Sold as a separate item to seal the switch
Non-Turn Washer
Seal
FIGURE C
Keyed Washer
Hex Nut
ORDERING INFORMATION: Single Shaft Switches, Add-A-Pot Switches
Series: ꢀetermined by the type of switch and
the angle of throw
Style*: Letter(s) from the Choices and Limitations chart
ꢁngle of Throw: Must agree with Series Number
Number of Decks: ꢁs limited by the angle of throw, the poles per deck, switch style and type of contacts
44M30–02–1–12N–F
Stop Arrangement: ꢁdd letter F to a one pole per deck switch with the maximum number of positions for
a stop between position 1 and the last position. Leave blank for continuous rotation
Type of Contacts: N = Non-shorting; S = Shorting
Positions Per Pole: Requires 02 positions as a minimum to maximum allowable dependent on the angle
of throw and poles per deck. Use ꢁJ for adjustable stops (Styles ꢀ and Uꢀ).
Poles Per Deck: ꢁs limited by angle of throw, switch series and style
* ꢁll rotary switches that are required to have military designated markings and testing adhering to MIL-3786 are to be ordered by specifying
the military part number identified on the appropriate slash sheet.
ORDERING INFORMATION: Concentric Shaft Rotary Switches
Series: ꢀetermined by the angle of throw, applicable to both sections
Style*: Letter(s) from the Choices and Limitations chart
Section A (front)
Number of Decks: ꢁs limited by the number of poles per deck
Poles Per Deck: ꢁs limited by the angle of throw
Positions Per Pole: Requires 02 positions as a minimum to the maximum allowable dependent on the angle
of throw and the poles per deck
Type of Contacts: N=Non-shorting, S=Shorting. ꢁll one pole per deck switches with the maximum number
of positions are continuous rotation
43M02110N–M03203S
Section B (rear)
The limitations listed for Section ꢁ apply to Section B
Type of Contacts
Positions Per Pole
Poles Per Deck
Number of Decks
Style
* ꢁll rotary switches that are required to have military designated markings and testing adhering to MIL-3786 are to be ordered by specifying
the military part number identified on the appropriate slash sheet.
Available from your local Grayhill Distributor For prices and discounts, contact a local Sales Office, an authorized local ꢀistributor or Grayhill.
Rotary
31
Grayhill, Inc.
• 561 Hillgrove Avenue • LaGrange, Illinois 60525-5997 • USA • Phone: 708-354-1040 • Fax: 708-354-2820 • www.grayhill.com