40DAWE_1.5 series
40W - Single Output - Wide Input - Isolated & Regulated
DC-DC Converter
DC-DC Converter
40 Watt
High efficiency up to 91%
2:1 wide input voltage range
Isolation voltage 1500VDC
Six-sided metal shield
Short circuit protection (SCP)
(automatic recovery)
Operating temperature:
The 40DAWE_1.5 series are isolated 40W DC-DC products with 2:1 input
voltage. They feature efficiency up to 91%, 1500VDC isolation, operating
temperature of -40°C to +85°C, output short circuit protection, over-
voltage protection, over-current protection , which make them widely
applied in data transmission device, battery power supply device,
telecommunication device, distributed power supply system, remote
control system, industrial robot fields.
-40°C to +85°C
Over voltage protection
Over current protection
Industry standard pinout
EN62368 approved
UL-62368-1 (E347551)
Common specifications
Cooling:
Output specifications
Free air convection
Item
Test condition
0%-100% load
Min Typ
Max
3
Units
%
Short circuit protection:
Operation temperature range:
Storage temperature range:
Vibration:
Hiccup, auto-recovery
-40°C~+85°C
Voltage accuracy
Line regulation
1
input voltage from low
to high @full load
0.2
0.5
%
-55°C~+125°C
Load regulation
0% to 100% load
1
%
10-55Hz, 10G, 30 Min. along X, Y and Z
300°C MAX, 1.5mm from case for 10 sec
300kHz TYP
Transient recovery 25% load step change
time
300
3
500
µs
Pin welding resistance temperature:
Switching frequency (PWM mode)*:
Humidity:
Transient respon-
se deviation
25% load step change
5
%
non-condensing, 95% MAX
Aluminum alloy
Temperature
coefficient
Full load
0.03
%/°C
Case material:
Potting material:
Epoxy (UL94V-0 rated)
500,000 hours
Ripple and noise*
Trim
20MHz Bandwidth
50
100
mV
MTBF (MIL-HDBK-217F @25°C)*:
Weight:
10
%Vo
%Vo
26.8g (Typ.) - 36g with heatsink
Over voltage
protection
Input voltage range
Input voltage range
110
160
190
Dimensions:
50.80 × 25.40 × 11.80 mm
51.40 × 26.20 × 16.50 mm (heatsink)
Over current
protection
110
%Io
* This series of products using reduced frequency technology, the switching
frequency is test value of full load. When the load is reduced to below 50%, the
* Test ripple and noise by “parallel cable” method.
Input specifications
Isolation specifications
Item
Test condition
Min
Typ
Max
Units
Item
Test condition
Min
Typ
Max
Units
VDC
Input current
(full load/no load)
• 24Vin
• 48Vin
1894/60
926/12
1938/100 mA
947/25
Isolation voltage
Input/Output, tested
for 1 minute and 1mA
max
1500
mA
Reflected ripple
current
Nominal input
voltage
30
mA
Isolation resistance
Test at 500VDC/60sec 1000
MΩ
pF
Isolation capacitance Input/Output,
100KHz/0.1V
2000
Surge voltage
(1s max.)
• 24Vin
• 48Vin
-0.7
-0.7
50
100
VDC
VDC
Input under-voltage • 24Vin
13
26
15.5
33
VDC
VDC
protection
• 48Vin
Example:
Starting voltage
• 24Vin
• 48Vin
18
VDC
VDC
40DAWE_2415S1.5
36
40 = 40Watt; D = DIP; A = series; W = wide input (2:1); E = Eco series;
9-36Vin; 15Vout; S = single output; 1.5 = 1500VDC isolation
Input filter
Hot plug
Pi type
Unavailable
• Module ON
Ctrl
Ctrl suspended or connected to
TTL high level (3.5-12VDC)
Ctrl pin connected to GND or low
level (0-1.2VDC)
Note:
(The voltage of Ctrl
pin is relative to
input pin GND.)
1. Input voltage can’t exceed this value, or will cause the permanent damage.
2. The load shouldn‘t be less than 5%, otherwise ripple will increase dramatically.
3. Max. Capacitive Load is tested on Vin-nominal and full load.
4. All specifications measured at Ta = 25°C, humidity <75%, nominal input voltage
and rated output load unless otherwise specified.
• Module OFF
• Input current
when switched OFF
5
10
mA
5. In this datasheet, all the test methods of indications are based on corporate
standards.
6. Only typical models listed, other models may be different, please contact our
technical person for more details.
7. Specifications subject to change without notice.
Page 1 of 5
40DAWE_1.5 – Rev. 2020-1.2
Specifications subject to change without notice.
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com