QUARTZ
EURO
HDA62 LVDS OSCILLATORS
11.4 x 9.6mm SMD 6 pad
DESCRIPTION
HDA62 series LVDS output oscillators cover the frequency range
750kHz to 800MHz. The design consists of a crystal operating in 3rd
overtone mode, without a PLL circuit.
OUTLINE & DIMENSIONS
SPECIFICATION
Frequency Range:
Output Logic
Phase Noise:
Frequency Stability:
Operating Temp Range
Commercial:
Industrial:
60MHz to 320.0MHz
LVDS
See table
See table
-10° to +70°C
-40° to +85°C
Input Voltage:
Output Logic
OH
+2.5VDC ±5% or +3.3VDC ±5%
High '1' V
:
1.4V typical, 1.6V max.
0.9V min., 1.1V typical
OL
Low '0' V :
Differential Output Voltage V
OD
:
247mV min., 355mV typ.,
454mV max. Output 1 - Output 2
OD
Differential Output Error dV : -50mV min., 50mV max.
OS
Output Offset Voltage V
:
OS
1.125V min., 1.20V typ., 1.375V max.
0mV min., 3mV typ., 25mV max.
0.7ns typical, 1.0ns max.
Offset Magnitude Error dV
Rise/Fall Times:
:
(20% to 80% of LVDS waveform)
Current Consumption
(15pF load):
Load:
Start-up Time:
Duty Cycle:
16mA max at 212.5MHz
50W from each output
5ms typ., 10ms max.
50%±5% (at 1.5V)
Drive Capability:
Input Static Discharge Prot:
100 Ohms between outputs
2kV min.
Storage Temperature Range:
Ageing:
-55°C to +150°C
±3ppm per year max., ±2ppm
thereafter. At T amb +25°C
Enable/Disable
No connection:
Disable:
Both outputs enabled
Both outputs are disabled when
control pad is taken below 0.3V
referenced to ground. Oscillator is
always 'on'. (Special request -
oscillator is off when disabled.)
Both Outputs are enabled when
control pad is taken above 0.7 Vcc
referenced to ground.
PHASE NOISE
(155.520MHz)
JITTER
(155.520MHz)
Offset
dBc/Hz
Typ. Max.
0.25ps 4.0ps
3.0ps
Enable:
10Hz
100Hz
1kHz
10kHz
100kHz
1MHz
10MHz
-72
Integrated Phase Jitter:
(12kHz to 20MHz)
Period Jitter:
(RMS)
Period Jitter:
-100
-125
-132
-142
-147
-149
ABSOLUTE MAXIMUM RATINGS
(Permanent damage may be caused if operated beyond these limits.)
Supply Voltage Vdd:
Input Voltage Vi:
Input Voltage Vo:
+4.6VDC max.
Vss -0.5 min., VDD +0.5V max.
Vss -0.5 min., Vdd +0.5V max.
21ps
(peak to peak)
PART NUMBERS
HDA62 oscillator part numbers are derived as follows:
Example:
3HDA622-A-250.000
STABILITY OVER TEMPERATURE RANGE
Stability
±ppm
Temperature Range Order Code
Supply Voltage
°C
25 = 2.5VDC
3 = 3.3VDC
Series Designation
Package Style
621 or 622
Stability Code
(See table)
Frequency
25
50
100
25
50
100
-10 to +70
-10 to +70
-10 to +70
-40 to +85
-40 to +85
-40 to +85
A
B
C
D
E
F
EUROQUARTZ LIMITED Blacknell Lane CREWKERNE Somerset UK TA18 7HE
Tel: +44 (0)1460 230000 Fax: +44 (0)1460 230001 Email: info@euroquartz.co.uk www.euroquartz.co.uk