QUARTZ
EURO
GW62 VCXO
CMOS SMD 11.4 x 9.6 x 2.5mm, 6 pad
50.1MHz ~ 800.0MHz
Frequency range 50.01MHz to 800MHz
LVCMOS Output
Supply Voltage 3.3 VDC
High Q fundamental mode crystal
Low jitter multiplier circuit
OUTLINE & DIMENSIONS
DESCRIPTION
GW62 VCXOs, are packaged in an industry-standard, 6 pad, 11.4 x
9.6 x 2.5mm SMD package. GW62 VCXOs incorporate a high Q
fundamental crystal and a low jitter multiplier circuit.
SPECIFICATION
Frequency Range:
Supply Voltage:
50.01MHz to 800.0MHz
3.3 VDC ±5%
Output Logic:
LVCMOS
Integrated Phase Jitter:
2.6ps typical, 4.0ps maximum
(for 155.250MHz)
Period Jitter RMS:
Period Jitter Peak to peak:
Phase Noise:
4.3ps typical (for 155.250MHz)
27.0ps typical (for 155.250MHz)
See table below
Initial Frequency Accuracy:
Tune to the nominal frequency
with Vc= 1.65 ±0.2VDC
90% Vdd minimum
10% Vdd maximum
From ±30ppm to ±150ppm
See table
Output Voltage HIGH (1):
Output Voltage LOW (0):
Pulling Range:
Temperature Stability:
Output Load:
15pF
Start-up Time:
Duty Cycle:
Rise/Fall Times:
Current Consumption
<96MHz:
10ms maximum, 5ms typical
50% ±5% measured at 50% Vdd
1.2ns typical (15pF load)
30mA maximum (15pF load)
40mA maximum (15pF load)
10% maximum, 6% typical
25kHz minimum
>96MHz:
Linearity:
Modulation Bandwidth:
Input Impedance:
Slope Polarity:
2 MW minimum
Monotonic and Positive. (An
increase of control voltage
always increases output
frequency.)
(Transfer function)
PHASE NOISE
Storage Temperature:
Ageing:
Enable/Disable (Tristate):
-50° to +100°C
±5ppm per year maximum
Pads 2 or 5, Enable high or 70%
Vdd min applied to Tri-state pad
to enable output.
30% Vdd max. to disable output
(high impedance)
Offset
Frequency 155.25MHz
-65dBc/Hz
10Hz
100Hz
1kHz
10kHz
100kHz
1MHz
10MHz
-95dBc/Hz
-120dBc/Hz
-125dBc/Hz
-121dBc/Hz
-120dBc/Hz
-140dBc/Hz
RoHS Status:
Fully compliant
PART NUMBER SCHEDULE
FREQUENCY STABILITY
Example: 3GW62B-80N-155.25
Temp. Range
Stability Code Stability ±ppm
Supply Voltage
A
B
C
D
E
25
50
100
25
50
0°~+70°C
0°~+70°C
0°~+70°C
-40°~+85°C
-40°~+85°C
-40°~+85°C
3 = +3.3V
Series Designator
GW62
Stability over
temperature range (See table)
F
100
Pullability in ±ppm
If non-standard frequency stability is required
Use ‘I’ followed by stability, i.e. I20 for ±20ppm
Pullability determinator
N = minimum
M = maximum
T = Typical
Frequency in MHz
EUROQUARTZ LIMITED Blacknell Lane CREWKERNE Somerset UK TA18 7HE
Tel: +44 (0)1460 230000 Fax: +44 (0)1460 230001 info@euroquartz.co.uk www.euroquartz.co.uk