Datasheet > 306024-8

306024-8

更新时间： 2024-10-31 01:06:15

品牌	Logo	应用领域
MACOM		/
页数	文件大小	规格书
6页	146K
描述
Read these instructions and referenced documents before crimping any splices

阅读下载

中文翻译

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

306024-8 数据手册

Instruction Sheet

Die Assemblies 45218, 45221,

69303-2, and 69820

408-1634

04 JAN 10 Rev C

Insert Anvil

(Moving Die)

Dimensions on this instruction sheet are in

NOTE

millimeters [with inches in brackets]. Figures are

not drawn to scale.

Insert Indenter

(Stationary Die)

Reasons for reissue of this instruction sheet are

provided in Section 8, REVISION SUMMARY.

Screw

2. DESCRIPTION

Ejector

The die assembly consist of an insert indenter

(moving die) and an insert anvil (stationary die).

The stationary die is identified by the chamfered

corners. The stationary die is marked with the die

assembly part number, wire size (AWG), and splice

type. When mated, the die assembly forms one

crimping chamber. Each die is secured in the tool by

a single screw.

Locator (Except Die

Assembly 69820)

DIE ASSEMBLY

PART

SPLICE

MINIMUM OPENING

DIAMETER

MARKING

SIZE

NUMBER

3. DIE INSTALLATION

Install the die assembly onto the tool according to the

instructions supplied with the tool. If using the

pneumatic tooling assembly, follow the instructions

supplied with the applicable crimper or adapter.

18--16

45218

22--14

—

ECV--ECN

18--10

ECV--ECN

45221

22--10

22--16

69303--2

69820

18--16 EC

6.73 mm [.265 in.]

6.48 mm [.255 in.]

4. CRIMPING PROCEDURE

18--16 ECVG

22--16

Die Assembly 69820 requires an insulation crimp

adjustment. Before crimping any splices, refer to

Section 5 for proper adjustment.

NOTE

Figure 1

1. INTRODUCTION

1. Select proper wire combinations as stated in the

applicable wire combination chart specified in

Figure 2. Strip wires to length indicated in Figure 2.

Do not use wires with nicked or missing strands.

Die Assemblies 45218, 45221, 69303--2 (shown in

Figure 1), and 69820 are used with the following tools

to crimp vinyl closed--end splices and nylon

closed--end splices onto solid and stranded wire sizes

22 through 10 AWG. For specific information

concerning the tools, refer to instruction sheet

(408--series) or customer manual (409--series) listed.

If conductors are twisted together to form a tight

bundle before inserting them into the splice, the

strip length must be maintained after twisting.

NOTE

REFERENCE

DOCUMENT

2. Insert the splice, wire barrel first, into the ejector

of the stationary die until splice bottoms. For nylon

splices, the shoulder must rest against the ejector;

for vinyl splices, the end of the wire barrel of must

rest against the locator. Die Assembly 69820 does

not have a locator; therefore, the wire barrel must

rest against the wire barrel section of the die. See

Figure 3. Close dies until splice is held in place.

TOOL

Straight Action Hand Tool 69710--1

408--2095

626 Pneumatic Tooling Assembly

189721--1 or 189722--1

Fitted with Straight Action Crimper

217200--1 or 189721--2

409--5862

408--4195

626 Pneumatic Tooling Assembly

189722--2

Fitted with C--Head Pneumatic Adapter

318161--1

3. Insert stripped wires into splice wire barrel until

conductors bottom. See Figure 3.

409--5862

408--4190

Always keep fingers clear of dies during tool

operation.

DANGER

Read these instructions and referenced documents

before crimping any splices.

TOOLING ASSISTANCE CENTER 1-800-722-1111

PRODUCT INFORMATION 1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.tycoelectronics.com

E2010 Tyco Electronics Corporation, Harrisburg, PA

All International Rights Reserved

1 of 6

TE logo and Tyco Electronics are trademarks.

LOC B

*Trademark. Other products, logos, and company names used are the property of their respective owners.

12 3 4 5 6

中文翻译

下载PDF

与306024-8相关器件

型号	品牌	获取价格	描述	数据表
306027-6	MACOM	获取价格	Read these instructions and referenced documents before crimping any splices
306027-6	TE	获取价格	This instruction sheet provides application instructions, maintenance, and inspection proc
306027-7	TE	获取价格	This instruction sheet provides application instructions, maintenance, and inspection proc
306027-7	MACOM	获取价格	Read these instructions and referenced documents before crimping any splices
306027-9	TE	获取价格	This instruction sheet provides application instructions, maintenance, and inspection proc
3060283	PHOENIX	获取价格	Modular Terminal Block
306028-7	MACOM	获取价格	Read these instructions and referenced documents before crimping any splices
306029-7	MACOM	获取价格	Read these instructions and referenced documents before crimping any splices
3060319	PHOENIX	获取价格	Modular Terminal Block
3060335	PHOENIX	获取价格	Terminal Block Accessory,

与306024-8相关文章

三星深化印度制造布局，供应链本地化进程加速
2024-10-29

19
芯擎科技“星辰一号”自动驾驶芯片点亮成功，2025年量产在即
2024-10-29

20
纳微科技震撼发布GaNSlim革新氮化镓功率芯片
2024-10-18

45
意法半导体发布第四代SiC技术，助力电动汽车电驱
2024-10-15

52

产品中心

服务支持

精选活动

关于我们

帮助中心

306024-8

306024-8 数据手册

与306024-8相关器件

与306024-8相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

306024-8

306024-8 数据手册

与306024-8相关器件

与306024-8相关文章

您还可以找

您在本页遇到什么问题？