.100″ ꢀ .100″ Low Profile Header
Straight & Right Angle, 4 Wall, High Temp Option
2500 Series
Table 2
Table 1
Pin Cross Section
Dimensions
Pin
Qty
Polarizing
Notches
Tail
X2
03
Dim E
Dimension F
Diagonals
Corner Radii
A
B
Dim G ꢁ .003
.112
[ 2.84]
.0075 Ref
[0.191]
.035 [0.89]
(See Note 2)
.0245 ꢁ .0005 .028 ꢁ .001
[0.622] [0.71]
10
14
.788 [20.02]
.988 [25.10]
.708 [17.98]
.908 [22.06]
B C
.155
[ 3.94]
.0075 Ref
[0.191]
.035
[0.89]
.0245 ꢁ .0005 .028 ꢁ .001
B C D E
[0.622]
[0.71]
.61 Ref
[15.5]
.003 Max
[0.08]
.045
[1.14]
.0250 ꢁ .002
[0.635]
.035 ꢁ .003
[0.90]
05
16
1.088 [27.64] 1.008 [25.60] A B C D E
20
24
26
30
34
40
50
60
64
1.288 [32.72] 1.208 [30.68] A B C D E
1.488 [37.80] 1.408 [35.76] A B C D E
1.588 [40.34] 1.508 [38.30] A B C D E
1.788 [45.42] 1.708 [43.38] A B C D E
1.988 [50.50] 1.908 [48.46] A B C D E
2.288 [58.12] 2.208 [56.08] A B C D E
2.788 [70.82] 2.708 [68.78] A B C D E
3.288 [83.52] 3.208 [81.48] A B C D E
3.488 [88.60] 3.408 [86.56] A B C D E
B
.250 [6.35]
.194 [4.93]
.228 [5.79]
Notch D
Notch E
.338
[8.59]
.100 Ref
[2.54]
Notch C
(See Table 1 & Note 1)
.100 Ref
[2.54]
Position 1
Straight
Notch B
(See Table 1)
Notch A
(See Table 1 & Note 1)
.165 [4.19]
Position 1 Orientation
Triangle
.025 ꢁ .002 Sq Ref
[0.64]
J
.253
[6.43]
.370
[9.40]
.298 [7.57]
E ꢁ .01
J
F Typ
Bend Pad
.100 Ref
A
[2.54]
.400
[10.16] Distance
Min End Stackable
.250 [6.35]
Section J–J
Min Side
Stackable
Distance
.172 ꢁ .003
[4.37]
G Dia
.050 ꢁ .003
[1.27]
ꢂ .035 ꢁ .003
[0.89]
.100 ꢁ .003
[2.54]
Optional Hole for
Polarization Peg
Position 1 as indicated
by Triangle
Inch
[mm]
.100 ꢁ .003
[2.54]
Tolerance Unless Noted
.0
.00 .000
Recommended P.C. Board Hole Pattern
(Shown for mounting side of board.)
Inch
± .1 ± .01 ± .005
Notes:
1. Notches ‘‘A’’ and ‘‘C’’ will accommodate 3M Polarizing Keys 3518.
2. The recommended PCB hole size for the kinked tail positions on the .112″ solder tail connector is .035″ ± .002.
[
] Dimensions for
Reference Only
Refer to TS-0972 for the positions kinked.
Ordering Information
X25XX-X0XXXX
Blank = Standard
Mating Plating Thickness:
Solder Tail Versions
UG = 15 µ″ [ 0.38 µm ]
UB = 30 µ″ [ 0.76 µm ]
Wrap Tail Versions
N = High Temperature
Pin Quantity:
(See Table 1)
Tail
02 = Solder Tails for .062 [ 1.57 ] Thick Board.
K2 = Kinked Solder Tails for .062 [ 1.57 ] Thick Board.
03 = Solder Tails for .094 to .125 [ 2.39 to 3.18 ] Thick Board.
05 = Wrap Tails for up to 3 Levels of Wire Wrap.
(Normal temp only)
Bend Pad Option:
EB = 30 µ″ [ 0.76 µm ]
(Normal temp Only)
6 = Straight pin product with bend
pad in High temp or normal plastics
7 = Straight pin product w/o bend pad in
High temp only
TS-0770-09
Sheet 2 of 3
3M Interconnect Solutions Division
6801 River Place Blvd.
Austin, TX 78726-9000
For technical, sales or ordering information call
800-225-5373