Instruction Sheet
Crimping Dies for SOLISTRAND*
and STRATO-THERM* Terminals
and Butt Splices
408-2648
17 MAY 13 Rev C
Refer to machine manual for crimp instructions.
1. INTRODUCTION
This instruction sheet provides instructions on product
application; and maintenance and inspection
procedures for crimping dies 69930, 69931, 69932,
69954, 69955, and 69956 used in the
AMP-TAPETRONIC* machine 69875; dies 68240-1,
68241-1, and 68242-1 are also used in the
AMP-TAPETRONIC machine 69875, or the Model “K”
AMP-O-LECTRIC* 565435-5, or the G-Terminating
Machine 354500-1.
3. CRIMP INSPECTION
Inspect crimped terminals and splices by checking the
features described in Figure 2. Use only the terminals
and splices that meet the conditions shown in the
“ACCEPT” column.
“REJECT” terminals and splices can be avoided
through careful use of instructions provided in the
machine manual and by preforming regular die
maintenance as instructed in Section 4,
MAINTENANCE/INSPECTION PROCEDURE, of this
instruction sheet.
These dies are used to crimp:
• SOLISTRAND terminals and butt splices on solid
or stranded copper wire sizes 22 thru 10.
• Uninsulated STRATO-THERM terminals and butt
splices (with wire insulation support) on solid or
stranded copper wire sizes 22 thru 10.
4. MAINTENANCE/INSPECTION PROCEDURE
It is recommended that a maintenance/inspection
program be performed periodically to ensure
dependable and uniform terminations. Dies should be
inspected at least once a month. Frequency of
inspection may be adjusted to suit your requirements
through experience. Frequency of inspection is
depend upon:
• Uninsulated STRATO-THERM terminals and butt
splices (without wire insulation support) on solid or
stranded copper wire sizes 22 thru 10.
Dies are coated with preservative to prevent rust and
corrosion. Wipe preservative from dies, particularly
from crimping surfaces.
1. The care, amount of use, and handling of the
dies.
Die insertion and removal and crimping instructions
are provided in the manual packaged with the
terminating machine. Section 2, INSTRUCTIONS,
provides personal safety and wire preparation
information. Section 3, CRIMP INSPECTION, features
terminal and splice crimp inspection procedures which
will enable you to establish and maintain a die
certification program.
2. The degree of operator skill.
3. The presence of abnormal amounts of dust and
dirt.
4. Your own established standards.
Since there is a possibility of die damage in shipment,
new dies should be inspected in accordance with
Section 4 when received in your plant.
For further instructions relative to the machines,
tooling adjustment, tape loading, etc., refer to the
instructions packaged with the machines.
NOTE
NOTE
i
4.1. Cleaning
Dimensions in this instruction sheet are in millimeters
[with inches in brackets]. Figures and illustrations are for
reference only and are not drawn to scale.
Do NOT allow deposits of dirt, grease, and foreign
matter to accumulate on the die closure surfaces and
on the bottoming surfaces of the dies. These deposits
may prevent the dies from bottoming fully and may
also cause excessive wear in the die closure surfaces,
thereby affecting the quality of the crimp. The dies
should be wiped clean frequently with a clean cloth.
Reasons for reissue of this instruction sheet are
provided in Section 5, REVISION SUMMARY.
2. INSTRUCTIONS
DANGER
Avoid personal injury. Always disconnect machine from
4.2. Visual Inspection
power supply when preforming adjustments, die
installation or removal, and machine maintenance.
Always keep guards and covers in place during normal
machine operation.
Visually inspect the die closure surfaces for chipped or
pitted conditions. Although dies may gage within
permissible limits, worn or damaged die closure
surfaces are objectionable and can affect the quality of
the crimp. Examples of possible damaged die
surfaces are shown in Figure 3.
For wire preparation, select the correct wire strip
length from Figure 1. Do NOT use wires with nicked or
missing conductor strands.
©2013 Tyco Electronics Corporation, a TE Connectivity Ltd. company TOOLING ASSISTANCE CENTER 1-800-722-1111 This controlled document is subject to change.
1 of 6
All Rights Reserved
*Trademark
PRODUCT INFORMATION 1-800-522-6752
For latest revision and Regional Customer Service,
visit our website at www.te.com
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or company names may be trademarks of their respective owners.
5秒后页面跳转
国产厂商思特威CMOS图像传感器芯片单月出货超1亿颗，技术创新引领行业发展
台积电5nm和3nm产能利用率达100%，半导体行业景气度持续攀升
AMD宣布全球裁员约1000人，调整战略聚焦增长
英伟达新AI芯片Rubin或提前半年亮相
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
