Document 617-1
Square Air Core Inductors
• Excellent Q factors – up to 130
• Current handling as high as 4.4 Amps!
Terminations RoHS compliant tin-silver over copper
Ambient temperature –40°C to +125°C with Irms current,
+125°C to +145°C with derated current
Storage temperature Component: –55°C to +125°C.
Packaging: –55°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Temperature Coefficient of Inductance ꢀTCLH +5 to +70 ppm/°C
Moisture Sensitivity Level ꢀMSLH 1 (unlimited floor life at <30°C
/ 85% relative humidity)
Mean Time Between Failures ꢀMTBFH 1 billion hours
PCB washing Only pure water or alcohol recommended
1. When ordering, please specify termination and packaging code:
0908SQ-27NJLC
SRF
typ4
DCR
max
Inductance2 Q3
Irms5
ꢀAH
Partnumber1
±±5 ꢀnꢁH
typ
ꢀMꢁzH ꢀmOhmH
Termination: L = RoHS compliant tin-silver (96.5/3.5) over copper.
Special order, added cost:
0806SQ-6N0JL_
0806SQ-8N9JL_
0806SQ-12NJL_
0806SQ-16NJL_
0806SQ-19NJL_
6.0
8.9
12.3
15.7
19.4
64
90
90
90
90
5200
4300
4800
4400
4000
6.0
7.0
8.0
9.0
10.0
2.9
2.9
2.9
2.9
2.9
T = RoHS tin-silver-copper (95.5/4/0.5) over copper
or S = non-RoHS tin-lead (63/37) over copper.
Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic
tape.
B = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge),
use code letter C instead.
0807SQ-6N9JL_
0807SQ-10NJL_
0807SQ-14NJL_
0807SQ-17NJL_
0807SQ-22NJL_
0908SQ-8N1JL_
0908SQ-12NJL_
0908SQ-17NJL_
0908SQ-22NJL_
0908SQ-27NJL_
6.9
10.2
13.7
17.0
22.0
8.1
12.1
16.6
21.5
27.0
100
100
100
100
100
130
130
130
130
130
4600
4000
4300
4000
3500
5200
4300
3400
3700
2600
6.0
7.0
8.0
9.0
10.0
6.0
7.0
8.0
9.0
10.0
2.7
2.7
2.7
2.7
2.7
4.4
4.4
4.4
4.4
4.4
D = 13″ machine-ready reel. EIA-481 embossed plastic
tape. Factory order only, not stocked.
2. Inductance measured at 400 MHz, 0.1 Vrms, 0 A using an Agilent/
HP 4287A LCR meter with an Agilent/HP 16193A test fixture.
3. Q measured at 400 MHz using an Agilent/HP 4291A impedance
analyzer.
4. SRF measured using an Agilent/HP 8753 network analyzer and a
Coilcraft SMD-D test fixture.
5. Current that causes a 20°C temperature rise from 25°C ambient.
6. Electrical specifications at 25°C.
See Qualification Standards section for environmental and test data.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
These parts are preproduction products for electrical evaluation
only. Specification subject to change without notice.
Document 617-1 Revised 10/02/07
© Coilcraft, Inc. 2007