5秒后页面跳转
08053C123MAT2A PDF预览

08053C123MAT2A

更新时间: 2024-10-29 11:28:15
品牌 Logo 应用领域
京瓷/艾维克斯 - KYOCERA AVX /
页数 文件大小 规格书
4页 519K
描述
X7R MLCC

08053C123MAT2A 数据手册

 浏览型号08053C123MAT2A的Datasheet PDF文件第1页浏览型号08053C123MAT2A的Datasheet PDF文件第3页浏览型号08053C123MAT2A的Datasheet PDF文件第4页 
X7R Dielectric  
Specifications and Test Methods  
Parameter/Test  
Operating Temperature Range  
Capacitance  
X7R Specification Limits  
Measuring Conditions  
Temperature Cycle Chamber  
-55ºC to +125ºC  
Within specified tolerance  
Freq.: 1.0 kHz ± 10%  
Voltage: 1.0Vrms ± .2V  
For Cap > 10µF, 0.5Vrm @ 120Hz  
≤ 10% for ≥ 50V DC rating≤ 12.5% for 25V DC rating  
≤ 12.5% for 25V and 16V DC rating  
≤ 12.5% for ≤ 10V DC rating  
Dissipation Factor  
Contact Factory for DF by PN  
100,000MΩ or 1000MΩ - µF,  
whichever is less  
Charge device with rated voltage for  
120 ± 5 secs @ room temp/humidity  
Insulation Resistance  
Charge device with 250% of rated voltage for 1-5 seconds, w/  
charge and discharge current limited to 50 mA (max)  
Note: Charge device with 150% of rated voltage for 500V devices.  
Dielectric Strength  
No breakdown or visual defects  
Appearance  
Capacitance  
Variation  
No defects  
≤ ±12%  
Resistance to  
Flexure  
Stresses  
Deflection: 2mm  
Test Time: 30 seconds  
Dissipation  
Meets Initial Values (As Above)  
≥ Initial Value x 0.3  
Factor  
Insulation  
Resistance  
≥ 95% of each terminal should be covered with  
fresh solder  
Dip device in eutectic solder at 230 ± 5ºC  
for 5.0 ± 0.5 seconds  
Solderability  
Appearance  
Capacitance  
Variation  
No defects, <25% leaching of either end terminal  
≤ ±7.5%  
Dissipation  
Dip device in eutectic solder at 260ºC for 60 seconds. Store at  
room temperature for 24 ± 2hours before measuring electrical  
properties.  
Meets Initial Values (As Above)  
Meets Initial Values (As Above)  
Meets Initial Values (As Above)  
Resistance to  
Solder Heat  
Factor  
Insulation  
Resistance  
Dielectric  
Strength  
Appearance  
Capacitance  
Variation  
No visual defects  
≤ ±7.5%  
Step 1: -55ºC ± 2º  
30 ± 3 minutes  
≤ 3 minutes  
Step 2: Room Temp  
Dissipation  
Factor  
Insulation  
Resistance  
Meets Initial Values (As Above)  
Meets Initial Values (As Above)  
Step 3: +125ºC ± 2º  
30 ± 3 minutes  
Thermal Shock  
Step 4: Room Temp  
≤ 3 minutes  
Dielectric  
Repeat for 5 cycles and measure after 24 ± 2 hours at room  
temperature  
Pre-treatment: After mounting, perform heat treatment 150+0/-  
10C for 2 hour, then stabilise for 24+/-2 hour at room temp,  
then measure.  
Meets Initial Values (As Above)  
No visual defects  
Strength  
Appearance  
Capacitance  
Variation  
≤ ±12.5%  
Dissipation  
Factor  
Insulation  
Resistance  
≤ Initial Value x 2.0 (See Above)  
≥ Initial Value x 0.3 (See Above)  
Charge device with ≥ rated voltage in test chamber set at  
125ºC ± 2ºC for 1000 hours (+48, -0).  
Load Life  
Pre-treatment: After remove from test chamber, perform heat  
treatment 150+0/-10C for 2 hour, then stabilise for 24+/-2 hour  
at room temp, then measure.  
Dielectric  
Strength  
Meets Initial Values (As Above)  
Contact AVX for datasheet of specific parts.  
Appearance  
Capacitance  
Variation  
No visual defects  
≤ ±12.5%  
Pre-treatment: After mounting, perform heat treatment 150+0/-  
10C for 2 hour, then stabilise for 24+/-2 hour at room temp,  
then measure.  
Dissipation  
Factor  
Insulation  
Resistance  
Dielectric  
Strength  
≤ Initial Value x 2.0 (See Above)  
≥ Initial Value x 0.3 (See Above)  
Load  
Humidity  
Store in a test chamber set at 85ºC ± 2ºC/ 85% ± 5% relative  
humidity for 1000 hours (+48, -0) with rated voltage applied.  
Pre-treatment: After remove from test chamber, perform heat  
treatment 150+0/-10C for 2 hour, then stabilise for 24+/-2 hour  
at room temp, then measure.  
Meets Initial Values (As Above)  
The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or  
available online at www.avx.com/disclaimer/ by reference and should be reviewed in full before placing any order.  
20  
073021  

与08053C123MAT2A相关器件

型号 品牌 获取价格 描述 数据表
08053C123MAT4A KYOCERA AVX

获取价格

X7R MLCC
08053C123MAZ2A KYOCERA AVX

获取价格

X7R MLCC
08053C123MAZ4A KYOCERA AVX

获取价格

X7R MLCC
08053C124J4T2A KYOCERA AVX

获取价格

Automotive MLCC
08053C124J4T4A KYOCERA AVX

获取价格

Automotive MLCC
08053C124J4Z2A KYOCERA AVX

获取价格

Automotive MLCC
08053C124J4Z4A KYOCERA AVX

获取价格

Automotive MLCC
08053C124JA79A KYOCERA AVX

获取价格

Ceramic Capacitor, Multilayer, Ceramic, 25V, 5% +Tol, 5% -Tol, X7R, 15% TC, 0.12uF, Surfac
08053C124JAT2A KYOCERA AVX

获取价格

CAP CER 0.12UF 25V X7R 0805
08053C124JAT4A KYOCERA AVX

获取价格

X7R MLCC