Axial Lead and Cartridge Fuses
Subminiature
V
LT-5™ Time Lag Extended Breaking Capacity Fuse 664 Series
®
U
D
E
® L
®
RoHS
• Similar to the 663 fuse, this fuse is designed with a higher
breaking capacity.
• Meets IEC 60127-3/4 specifications (up to 6.3A).
• Available in short and long lead variations.
ELECTRICAL CHARACTERISTICS:
% of Ampere
Rating
Ampere
Rating
Time
150%
800mA-6.3A
1 hour Min.
210%
275%
400%
1000%
800mA-6.3A
800mA-6.3A
800mA-6.3A
800mA-6.3A
2 minutes, Maximum
.4 sec Min.; 10 seconds Maximum
.1 sec Min.; 3 seconds Maximum
.02 sec Min. .15 seconds Maximum
100%
200%
8-10A
8-10A
4 hours, Min.
8.5(.335")
8.5(.335")
60 seconds, Maximum
AGENCY APPROVALS: IEC 60127-3/4: VDE and Semko approved
from 800mA to 4A. Recognized under the components program of
Underwriters Laboratories and recognized by CSA from 800mA to 6.3A.
Approved by KTL from 800mA to 6.3A. Approved by METI and CCC
from 1 to 4A. Listed by the Underwriters Laboratories for 8 and 10A rat-
ings.
0.64
(.025")
0.64
(.025")
INTERRUPTING RATINGS: 100A at 250 VAC.
5.08
(.200")
ENVIRONMENTAL SPECIFICATIONS:
Operating Temperature: -40˚C to +85˚C.
5.08
(.200")
Case Resistance: Min 100 Mohms, according to EIA/IS-722, 4.7
Vibration: 20gn, 20 min, 10Hz to 2,000Hz, 12 cycles according to
EIA/IS-722, 4.10 (Frequency range 10-2000Hz, cross-over frequency 60
Hz according to IEC 60068-2-6, test Fc)
Mechanical Shock: 50g, half sine wave, 11ms, 3 times each direction
according to IEC 60068-2-27.
Resistance to Cleaning Solvents: Clean according to EIA/IS-722, 4.11
Resistance to Soldering Heat: 10 sec. At 260˚C to IEC 60068-2-20,
test Tb
ORDERING INFORMATION:
Nominal
Resistance
Cold mOhms
Nominal
Catalog
Number
Ampere
Rating
Voltage
Rating
Melting I2t
A2 Sec
0664.800
0664 001.
0664 1.25
0664 01.6
0664 002.
0664 02.5
0664 3.15
0664 004.
0664 005.
0664 06.3
0664 008.
0664 010.
.800
1.00
1.25
1.60
2.00
2.50
3.15
4.00
5.00
6.30
8.00
10.00
250
250
250
250
250
250
250
250
250
250
250
250
168
123
85
60
39
30
20
17
11
9
2.2
4.4
6.3
10
16
32
57
77
155
262
397
440
Terminal Strength: Tensile load min. 9N, according to EIA/IS-722, 4.5.5
PHYSICAL SPECIFICATIONS:
Materials: Temperature Resistant Body, UL 94V-0; Sn Coated Copper
Wire Terminals.
Solderability: IEC 60068-2-20, test Ta
Soldering Parameters: Wave Solder – 235˚C, 2 seconds maximum.
7
6
Refer to page 342 for LT-5TM holder information.
PACKAGING:
Please refer to the following suffixes when ordering:
• 100 Piece Bulk: Short Leads use suffix HXSL;
Long Leads use suffix HXLL
• 750 Piece Tape and Reel per IEC 286-2:
(Long Leads only) use suffix ZRLL
• 1000 Piece Ammo Pack use suffix MALL
PATENTED
449
w w w. l i t t e l f u s e. c o m