Document 773-1
Ferrite Chip Inductors
–
0603AF
•ꢀHigherꢀinductanceꢀvaluesꢀthanꢀceramicꢀ0603ꢀinductors
•ꢀHeavierꢀgaugeꢀwireꢀforꢀlowꢀDCR
•ꢀFerriteꢀconstructionꢀforꢀhighꢀcurrentꢀhandling
•ꢀInductanceꢀvaluesꢀfromꢀ15ꢀnHꢀtoꢀ10ꢀµH
Impedance typ (Ohms)
Inductance2
±±5 (nH)
SRF typ4
(MHz)
DCR max5
(Ohms)
Irms6
(A)
Color
code
Part number1
Qtyp3
100 MHz
±00 MHz
0603AF-15NXJR_
0603AF-33NXJR_
0603AF-111XJR_
0603AF-121XJR_
0603AF-241XJR_
15@7.9MHz
33@7.9MHz
110@7.9MHz
120@7.9MHz
240@7.9MHz
13@7.9MHz
13@7.9MHz
15@7.9MHz
15@7.9MHz
15@7.9MHz
10
19
70
76
140
42
90
350
410
810
3500
2300
1230
1150
900
0.023
0.028
0.060
0.089
0.12
2.1
1.9
1.6
1.4
0.85
Yellow
Red
Red
Black
Violet
0603AF-271XJR_
0603AF-471XJR_
0603AF-561XJR_
0603AF-681XJR_
0603AF-821XJR_
270@7.9MHz
470@7.9MHz
560@7.9MHz
680@7.9MHz
820@7.9MHz
15@7.9MHz
15@7.9MHz
16@7.9MHz
16@7.9MHz
16@7.9MHz
173
306
371
420
507
1023
2253
3180
3620
3300
750
575
515
530
325
0.22
0.37
0.49
0.46
0.58
0.68
0.61
0.53
0.49
0.42
Brown
Orange
Blue
Orange
Green
0603AF-102XJR_
0603AF-222XJR_
0603AF-472XJR_
1000@7.9MHz
2200@7.9MHz
4700@7.9MHz
17@7.9MHz
16@2.5MHz
16@7.9MHz
12@2.5MHz
663
5220
2100
1400
9823
129
220
150
400
85
60
0.84
1.10
1.50
4.50
0.40
0.32
0.26
0.18
Black
Red
Yellow
Gray
0603AF-103XJR_ 10000@2.5MHz
40
1. When ordering, please specify termination and packaging codes:
0603AF-102XJRW
Termination: R = RoHS compliant matte tin over nickel over silver-
platinum-glass frit.
Designer’s Kit C439 contains 10 each of all values
Environmental RoHS compliant, halogen free
Core material Ferrite
Terminations RoHS compliant matte tin over nickel over silver-plati-
num-glass frit. Other terminations available at additional cost.
Special order: T = RoHS tin-silver-copper
(95.5/4/0.5) or S = non-RoHS tin-lead (63/37).
Weight 4.3 – 5.7 mg
Ambient temperature –40°C to +85°C with Irms current, +85°C to
+100°C with derated current
Packaging: W = 7″ machine-ready reel. EIA-481 punched paper tape
(2000 parts per full reel).
U = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge),
use code letter W instead.
Storage temperature Component: –40°C to +100°C.
Packaging: –40°C to +80°C
2. Inductance measured at 0.1 Vrms, using Coilcraft SMD-A fixture
in Agilent/HP 4286A impedance analyzer with Coilcraft-provided
correlation pieces.
3. Q measured on Agilent/HP 4395A with Agilent/HP 16193 test fixture.
4. SRF measured using Agilent/HP 8753D network analyzer with
Coilcraft SMD-D test fixture.
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Temperature Coefficient of Inductance (TCL) +50 to +300 ppm/°C
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
5. DCR measured on Cambridge Technology Micro-ohmmeter.
6. Current that causes a 15°C temperature rise from 25°C ambient.
Because of their open construction, these parts will not saturate.
7. Electrical specifications at 25°C.
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
One per billion hours / one billion hours, calculated per Telcordia SR-332
Packaging 2000 per 7″ reel; Paper tape: 8 mm wide, 1.0 mm thick,
4 mm pocket spacing
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
PCB washing Only pure water or alcohol recommended
Specifications subject to change without notice.
Please check our website for latest information.
Document 773-1 Revised 03/15/11
© Coilcraft, Inc. 2011