20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
M
L
M
L
PACKAGING
TABLE OF CONTENTS
SHEET DESCRIPTION
NOTES AND BOM
MATING INTERFACE/CONNECTOR DRAWINGS
NOTES: VALID UNLESS OTHERWISE SPECIFIED
DESCRIPTION
DRAWING NO.
DESCRIPTION
INTERFACE DEFINITION
MOLEX INLINE
SHEET NO.
1. GENERAL:
1X2
PK-31300-635
1X2
*150-S-002-1-Z05
SD-33481-0001
1
2
a. APPLICATION SPECIFICATION SEE: AS-33472-100
-CONTAINS: PRODUCT INTRODUCTION, PRODUCT SUMMARY,
CONNECTOR ASSEMBLY, PACKAGING INFORMATION, CONNECTOR
MATING, SERVICE INSTRUCTIONS, ELECTRICAL CONTINUITY
CHECKING, CRIMPING, AND TROUBLESHOOTING.
CONFIGURATIONS
3-4
5
KEY CONFIGURATIONS
RECEPTACLE CONNECTOR ASSEMBLY
BACKSHELL NOTES
-DESIGNED TO MATE WITH DEVICE OR CONNECTOR AS SPECIFIED
IN THE MATING INTERFACE/CONNECTOR DRAWINGS CHART.
1X6
PK-31300-903
1X6
*150-S-006-1-Z03
SD-33481-0001
6
BACKSHELL
7
*DENOTES DRAWINGS THAT CAN BE ACCESSED AT <http://ewcap.uscarteams.org/>.
-ASSEMBLY SHIPPED WITH PLR IN PRE-LOCK POSITION
(SEE PLR PRE-LOCK VIEW SHEET 5).
K
J
H
G
F
E
D
C
K
J
H
G
F
E
D
C
8
BACKSHELL CONFIGURATIONS
b. PRODUCT SPECIFICATION SEE:
-STANDARD CONFIGURATION: PS-33471-000
-UL V0 CONFIGURATION: PS-160105-0001
CONTAINS: PRODUCT INTRODUCTION, PRODUCT SUMMARY,
RATINGS (CURRENT, TEMPERATURE, SEALING, AND FLAMMABILITY),
TERMINALS, WIRE DIAMETER RANGE, PRODUCT VALIDATION, AND PRODUCT DEVIATIONS.
c. PACKAGING SPECIFICATION PER MOLEX DRAWING: SEE PACKAGING CHART
d. PARTS MUST BE IN COMPLIANCE TO MOLEX CHEMICAL SUBSTANCES FOR
PRODUCTS AND PACKAGING SPECIFICATION: QEHS-699000-301
e. DATA MUST BE SUBMITTED UNDER THE MOLEX PART NUMBER TO IMDS
(COMPANY ID#13255)
2. DESIGN - MATERIALS:
1x2
a. FOR BILL OF MATERIALS SEE:
-STANDARD CONFIGURATION SD-33471-0002
-UL V0 CONFIGURATION SD-160105-0002
3. DESIGN - GEOMETRY:
a. THE 3-D CAD DATA IS BASIC (WITHOUT TOLERANCE) AND MASTER FOR THIS PART
WITH THE EXCEPTION OF UNDERLINED DIMENSIONS. DIMENSIONAL INFORMATION NOT SHOWN
ON THIS DRAWING IS DEFINED BY THE DATA FILE AT ITS LATEST REVISION.
b. GEOMETRIC DIMENSIONS AND TOLERANCES PER ASME Y14.5M-2009
c. EDGES AND UNDIMENSIONED DETAILS PER ISO13715
d. CORNERS SHOWN AS SHARP TO BE R 0.2 MAX.
e. LETTERING SHALL BE 0.15 MAX RAISED IN 0.25 MAX RECESS PAD.
THIS INCLUDES RECYCLING CODE, CAVITY ID, VENDOR IDENTIFICATION,
AND CUSTOMER MATERIAL NUMBER.
f. VISUAL DEFECTS SHALL MEET COSMETIC STANDARD PS-45499-002 (Class B).
g. LASER MARKING:
1. PART NUMBER
2. DAY OF THE YEAR
3. SHIFT
4. YEAR
FOR ADDITIONAL INFORMATION SEE SECTION 5 UNDER PROCEDURES IN ES-34735-008.
A1
A
UPDATED THE DRAWING FRAME
MINOR GEOMETRY CHANGE FOR UL V0
UPDATE VIEWSETS
2
1
INSPECTION NUMBER LOG
LAST NUMBER: 11
ADDED: 11
INITIAL RELEASE
REV DESCRIPTION
REMOVED:
REV
THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
FUNCTIONAL
SYMBOLS
DIMENSION UNITS
SCALE
CURRENT REV DESC:
=
=
=
mm 1.5:1
0
0
0
GENERAL TOLERANCES
(UNLESS SPECIFIED)
MX150 RCPT
SINGLE ROW SEALED ASSY MAT SEAL
ANGULAR TOL
4 PLACES
3 PLACES
2 PLACES
1 PLACE
±
±
±
±
±
±
1.0 °
EC NO: 643941
DRWN: XLDONG03
CHK'D: JDENG02
APPR: JDENG02
INITIAL REVISION:
DRWN: APROFFITT
2020/08/21
2020/08/26
2020/08/26
B
A
DIVISIONAL
SYMBOLS
B
A
PRODUCT CUSTOMER DRAWING
0.1
0.2
DOCUMENT NUMBER
DOC TYPE DOC PART REVISION
2015/11/04
PSD 001
SD-33471-0001
A1
0 PLACES
APPR: KDEKOSHI
THIRD ANGLE PROJECTION
2016/06/14
SERIES
1x6
DRAWING
MATERIAL NUMBER
CUSTOMER
SHEET NUMBER
DRAFT WHERE APPLICABLE
MUST REMAIN
SEE NOTE 2a
GENERAL MARKET
1 OF 8
D-SIZE 33471
DOCUMENT STATUS P1 RELEASE DATE 2020/08/26
07:23:52
WITHIN DIMENSIONS
FORMAT: master-tb-prod-D
REVISION: J
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
DATE: 2020/01/14