13
12
11
10
9
8
7
6
5
4
3
2
1
LENGTH
ꢁꢂꢃꢀ>ꢁꢄꢅ@
WIDTH
PART NO.
CIRCUITS
ꢁꢂꢂꢆꢀ>ꢁꢃꢂ@
.283 [7.2]
.283 [7.2]
.283 [7.2]
.283 [7.2]
.283 [7.2]
.307 [7.8]
.307 [7.8]
.307 [7.8]
.307 [7.8]
.307 [7.8]
.331 [8.4]
.331 [8.4]
.331 [8.4]
.331 [8.4]
.331 [8.4]
.354 [9.0]
.354 [9.0]
.354 [9.0]
.354 [9.0]
.354 [9.0]
.403 [10.2]
.403 [10.2]
.403 [10.2]
NOTES:
2.00 [50.8]
4.00 [101.6]
6.00 [152.4]
8.00 [203.2]
10.00 [254.0]
2.00 [50.8]
150150223
150150423
150150623
150150823
150151023
150150225
150150425
150150625
150150825
150151025
150150227
150150427
150150627
150150827
150151027
150150229
150150429
150150629
150150829
150151029
150150233
150150433
150150633
23
23
23
23
23
25
25
25
25
25
27
27
27
27
27
29
29
29
29
29
33
33
33
J
J
1. SUBSTRATE AND COVERLAY MATERIAL IS .001 [25uM] POLYIMIDE.
2. CONDUCTOR IS 1/2 OZ (.0007) [18uM] COPPER.
3. PLATING IS 2 MICRO INCHES MINIMUM OF HARD GOLD OVER 100 MICRO INCHES MINIMUM OF NICKEL.
4. TAIL ENDS ARE .008 [.20] THICK.
5. JUMPER CABLES ARE SUITABLE FOR USE WITH MOLEX 502598 SERIES CONNECTOR.
I
I
4.00 [101.6]
6.00 [152.4]
8.00 [203.2]
10.00 [254.0]
2.00 [50.8]
LENGTH
ꢁꢃꢃꢇꢁꢂꢄꢀ>ꢈꢁꢂꢂꢂꢁꢅꢂ@
EXPOSED CIRCUITS
BOTH ENDS
4.00 [101.6]
6.00 [152.4]
8.00 [203.2]
10.00 [254.0]
2.00 [50.8]
(NOTE 4)
H
G
F
E
D
C
B
A
H
G
F
E
D
C
B
A
.0118
.0118
[.30]
[.30]
4.00 [101.6]
6.00 [152.4]
8.00 [203.2]
10.00 [254.0]
2.00 [50.8]
WIDTH
4.00 [101.6]
6.00 [152.4]
.0118 [.30] .0118 [.30]
x (N+1)
FRONT
8.00 [203.2]
10.00 [254.0]
2.00 [50.8]
.403 [10.2]
.403 [10.2]
.472 [12.0]
.472 [12.0]
.472 [12.0]
.472 [12.0]
.472 [12.0]
.543 [13.8]
.543 [13.8]
.543 [13.8]
.543 [13.8]
.543 [13.8]
.614 ]15.6]
.614 ]15.6]
.614 ]15.6]
.614 ]15.6]
.614 ]15.6]
150150833
150151033
150150239
150150439
150150639
150150839
150151039
150150245
150150445
150150645
150150845
150151045
150150251
150150451
150150651
150150851
150151051
33
33
39
39
39
39
39
45
45
45
45
45
51
51
51
51
51
x (N-1)
4.00 [101.6]
6.00 [152.4]
8.00 [203.2]
10.00 [254.0]
2.00 [50.8]
ꢁꢃꢅꢉꢁꢂꢄꢀ>ꢆꢁꢂꢂꢂꢁꢅꢂ@
TAIL STIFFENER
BOTH ENDS
R.008 [R.20]
TYP. (4)
4.00 [101.6]
6.00 [152.4]
8.00 [203.2]
10.00 [254.0]
2.00 [50.8]
N = NUMBER OF CONDUCTORS
JUMPER END DETAIL
33 CIRCUIT SHOWN
4.00 [101.6]
6.00 [152.4]
8.00 [203.2]
10.00 [254.0]
REAR
DIMENSION STYLE
SCALE
DESIGN UNITS
GENERAL TOLERANCES
(UNLESS SPECIFIED)
THIRD ANGLE
PROJECTION
15015 _ _ _ _
INCH [MM]
NONE
METRIC
DRAWN BY
DATE
DATE
DATE
TITLE
INCH
---
.010
.030
---
mm
.3MM PITCH
JUMPER CABLES
NUMBER OF CIRCUITS
LENGTH
SERIES NUMBER
0
0
4 PLACES ---
=
=
CHECKED BY
APPROVED BY
MATERIAL NO.
3 PLACES ---
2 PLACES ---
C
1 PLACE
---
Molex
MOLEX INCORPORATED
$1*8/$5ꢀ1
SHEET NO.
DOCUMENT NO.
DRAFT WHERE
APPLICABLE
SEE CHART
SD-15015-001
PART NUMBER CONSTRUCTION
SIZE
MUST REMAIN
THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX
INCORPORATED AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
WITHIN DIMENSIONS
B
C
13
12
11
10
9
8
7
6
5
4
3
2
1