Kintex-7 FPGAs Data Sheet:
DC and AC Switching Characteristics
DS182 (v2.8) March 4, 2014
Product Specification
Introduction
Kintex®-7 FPGAs are available in -3, -2, -1, and -2L speed
grades, with -3 having the highest performance. The -2L
device). However, only selected speed grades and/or
devices are available in each temperature range.
devices can operate at either of two V
voltages, 0.9V
CCINT
All supply voltage and junction temperature specifications
are representative of worst-case conditions. The
parameters included are common to popular designs and
typical applications.
and 1.0V and are screened for lower maximum static power.
When operated at V = 1.0V, the speed specification of
CCINT
a -2L device is the same as the -2 speed grade. When
operated at V = 0.9V, the -2L performance and static
CCINT
and dynamic power is reduced.
Available device and package combinations can be found in
:
Kintex-7 FPGA DC and AC characteristics are specified in
commercial, extended, industrial, and military temperature
ranges. Except for the operating temperature range or
unless otherwise noted, all the DC and AC electrical
parameters are the same for a particular speed grade (that
is, the timing characteristics of a -1 speed grade military
device are the same as for a -1 speed grade commercial
•
•
7 Series FPGAs Overview (DS180)
Defense-Grade 7 Series FPGAs Overview (DS185)
This Kintex-7 FPGA data sheet, part of an overall set of
documentation on the 7 series FPGAs, is available on the
Xilinx website at www.xilinx.com/7.
DC Characteristics
Table 1: Absolute Maximum Ratings
(1)
Symbol
FPGA Logic
VCCINT
Description
Min
Max
Units
Internal supply voltage
Auxiliary supply voltage
–0.5
–0.5
–0.5
–0.5
–0.5
–0.5
–0.5
–0.40
–0.55
–0.40
1.1
2.0
V
V
V
V
V
V
V
V
V
V
VCCAUX
Supply voltage for the block RAM memories
Output drivers supply voltage for 3.3V HR I/O banks
Output drivers supply voltage for 1.8V HP I/O banks
Auxiliary supply voltage
1.1
VCCBRAM
3.6
VCCO
2.0
2.06
VCCAUX_IO
VREF
Input reference voltage
2.0
I/O input voltage for 3.3V HR I/O banks
I/O input voltage for 1.8V HP I/O banks
VCCO + 0.55
VCCO + 0.55
2.625
(2)(3)(4)
VIN
I/O input voltage (when VCCO = 3.3V) for VREF and differential I/O standards except
TMDS_33(5)
Key memory battery backup supply
–0.5
2.0
V
VCCBATT
GTX Transceiver
VMGTAVCC
Analog supply voltage for the GTX transmitter and receiver circuits
Analog supply voltage for the GTX transmitter and receiver termination circuits
Auxiliary analog Quad PLL (QPLL) voltage supply for the GTX transceivers
GTX transceiver reference clock absolute input voltage
–0.5
–0.5
–0.5
–0.5
1.1
1.32
1.935
1.32
V
V
V
V
VMGTAVTT
VMGTVCCAUX
VMGTREFCLK
© 2011–2014 Xilinx, Inc. XILINX, the Xilinx logo, Virtex, Kintex, Artix, Zynq, Spartan, ISE, Vivado and other designated brands included herein are trademarks of Xilinx in the
United States and other countries. All other trademarks are the property of their respective owners.
DS182 (v2.8) March 4, 2014
Product Specification
www.xilinx.com
Send Feedback
1