Datasheet > WQCW2520Z0JR20PB

WQCW2520Z0JR20PB

更新时间： 2024-04-09 18:56:48

品牌	Logo	应用领域
华新科技 - WALSIN		/
页数	文件大小	规格书
7页	269K
描述
SMD Wire Wound Ceramic Chip RF Inductor(AEC-Q200) / WQCW Series 200, 50, 500mA

阅读下载

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

WQCW2520Z0JR20PB 数据手册

RELIABILITY PERFORMANCE

Test Item

Test Condition

Standard Source

1000 hrs. at rated operating temperature (e.g. 125°C part

can be stored for 1000 hrs. @ 125°C. Same applies f or

105°C and 85°C. Unpowered.

High Temperature

Exposure (Storage)

MIL-STD-202

Method 108

Measurement at 24±4 hours after test conclusion.

1000 cycles (-40°C to +125°C). Note: If 85°C part o r 105°C

part the 1000 cycles will be at that temperature.

Measurement at 24±4 hours after test conclusion. 30min

maximum dwell time at each temperature extreme. 1 min.

maximum transition time.

JESD22

Method JA-104

Temperature Cycling

1000 hours 85°C/85%RH. Unpowered.

Measurement at 24±4 hours after test conclusion.

MIL-STD-202

Method 103

Biased Humidity

Operational Life

1000 hrs. @ 105°C. If 85°C or 125°C part will be te sted at

that temperature.

MIL-PRF-27

Measurement at 24±4 hours after test conclusion.

Method 213. Condition C,

Peak Value: 100g’s, Duration: 6ms, Waveform: Half-sine

Velocity Change: 12.3ft/sec

MIL-STD-202

Method 213

Mechanical Shock

Vibration

5g's for 20 minutes, 12 cycles each of 3 orientations.

Note: Use 8"X5" PCB, .031" thick, 7 secure points on one

long side and 2 secure points at corners of opposite sides.

Parts mounted within 2" from any secure point. Test from

10-2000 Hz.

MIL-STD-202

Method 204

Condition B No pre-heat of samples. Note: Single Wave

Solder - Procedure 2 for SMD and Procedure 1 for Leaded

with solder within 1.5mm of device body.

Resistance to Soldering

Heat

MIL-STD-202

Method 210

Passive Component Human Body Model (HBM)

Electrostatic Discharge (ESD) Test.

Only direct contact discharge, record the voltage value

what the sample can pass.

AEC-Q200-002

ISO/DIS10605

ESD

For both Leaded & SMD. Electrical Test not required.

Magnification 50X. Conditions:

Leaded: Method A @ 235°C, category 3. SMD:

a) Method B, 4 hrs @ 155°C dry heat @ 235°C

b) Method B @ 215°C category 3.

Solderability

J-STD-002

c) Method D category 3 @ 260°C.

Flammability

Board Flex

V-0 or V-1 Acceptable

UL-94

60 sec minimum holding time.

Force of 1.8kg for 60 seconds.

AEC-Q200-005

AEC-Q200-006

Terminal Strength

(SMD)

Page 5 of 7

ASC_WQCW2520 Series_Auto

Nov. 2018

1 2 3 456 7

下载PDF

与WQCW2520Z0JR20PB相关器件

型号	品牌	描述	获取价格	数据表
WQCW2520Z0JR22PB	WALSIN	SMD Wire Wound Ceramic Chip RF Inductor(AEC-Q200) / WQCW Series 220, 45, 500mA	获取价格
WQCW2520Z0JR24PB	WALSIN	SMD Wire Wound Ceramic Chip RF Inductor(AEC-Q200) / WQCW Series 240, 50, 500mA	获取价格
WQCW2520Z0JR27PB	WALSIN	SMD Wire Wound Ceramic Chip RF Inductor(AEC-Q200) / WQCW Series 270, 45, 500mA	获取价格
WQCW2520Z0JR30PB	WALSIN	SMD Wire Wound Ceramic Chip RF Inductor(AEC-Q200) / WQCW Series 300, 45, 660mA	获取价格
WQCW2520Z0JR33PB	WALSIN	SMD Wire Wound Ceramic Chip RF Inductor(AEC-Q200) / WQCW Series 330, 45, 450mA	获取价格
WQCW2520Z0JR36PB	WALSIN	SMD Wire Wound Ceramic Chip RF Inductor(AEC-Q200) / WQCW Series 360, 45, 660mA	获取价格