THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX
(630) 851-5040.
PHONE (630) 851-4722.
WWW.CONWIN.COM
P R O D UC T D ATA S H E E T
CRYSTAL CONTROLLED OSCILLATORS
CW
0639
VSPLD63TE
622.08M
3.3V SURFACE MOUNT VCSO OSCILLATOR
VSPLD63TE
ABSOLUTE MAXIMUM RATINGS
PARAMETER
TABLE 1.0
NOTE
UNITS
MINIMUM NOMINAL MAXIMUM
UNITS
°C
Storage Temperature
Supply Voltage
-55
-0.5
-0.5
-
-
-
125
7.0
7.0
DESCRIPTION
(Vcc)
(Vc)
Vdc
Vdc
Control Voltage
The Connor-Winfield
VSPLD63TE is a 3.3V Voltage
Controlled SAW Oscillator
(VCSO) with Differential LVPECL
outputs and Enable/Disable
function. The VSPLD63TE is
designed for use with PLL
systems in SONET/SDH systems
requiring low jitter and wide pull
range over the industrial
OPERATING SPECIFICATIONS
PARAMETER
TABLE 2.0
NOTE
MINIMUM NOMINAL MAXIMUM
UNITS
MHz
-
-
Center Frequency
(Fo)
622.08
Frequency Stability
-
+/-150
-
ppm
1
Operating Temperature Range
Supply Voltage
-40
-
3.3
-
85
°C
(Vcc)
(Icc)
3.135
3.465
Vdc
Supply Current
-
-
-
-
-
-
-
80
mA
Jitter (BW=10Hz to 20MHz)
Jitter (BW=12kHz to 80MHz)
SSB Phase Noise at 100Hz offset
SSB Phase Noise at 1KHz offset
SSB Phase Noise at 10KHz offset
SSB Phase Noise at 100KHz offset
-
3.0
ps rms
ps rms
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
-
0.5
temperature range. No
multiplication schemes are used
in this oscillator design.
-70
-105
-145
-155
-
-
-
-
FEATURES
INPUT CHARACTERISTICS
PARAMETER
TABLE 3.0
NOTE
MINIMUM NOMINAL MAXIMUM
UNITS
Vdc
VOLTAGE CONTROLLED SAW
OSCILLATOR
Control Voltage Range
Absolute Pull Range (APR)
Gain Transfer (Kv)
(Vc)
0.3
1.65
3.0
+/-50
-
-
ppm
2
-
-15
-
175
-
ppm/volt
%
LOW PROFILE, SURFACE MOUNT
PACKAGE
Monotonic Linearity
-
15
Input Impedance
50K
-
Ohm
KHz
3.3V OPERATION
-
-
-
Modulation Bandwidth (3dB)
Enable Input Voltage (Low)
Disable Input Voltage (High)
10
-
-
1.68
-
(Vil)
Vdc
3
3
LOW JITTER <0.5pS RMS
(Vih)
2.275
Vdc
ABSOLUTE PULL RANGE (APR): ±50ppm
TEMPERATURE RANGE: -40 to 85°C
DIFFERENTIAL LVPECLOUTPUTS
ENABLE / DISABLE FUNCTION
TAPEAND REEL PACKAGING
RoHS 5/6 COMPLIANT
LOW VOLTAGE PECL OUTPUT CHARACTERISTICS
TABLE 4.0
PARAMETER
MINIMUM NOMINAL MAXIMUM
UNITS
Ohms
Vdc
Vdc
%
NOTE
LOAD
-
-
-
50
-
4
Voltage
(High)
(Low)
(Voh)
(Vol)
2.275
-
45
-
-
1.68
55
Duty Cycle at 50% Level
50
250
Rise and fall times (Measured 20% to 80%)
400
ps
PACKAGE CHARACTERISTICS
TABLE 5.0
Package
Non-hermetic package consisting of an FR4 substrate with grounded metal
cover.
PROCESS RECOMMENDATIONS
Soldering Process
Wash
TABLE 6.0
See solder profile page 2.
Ultrasonic cleaning is not recommended.
ORDERING INFORMATION
VSPLD63TE - 622.08MHz
Notes
VCSO
SERIES
CENTER
FREQUENCY
1.0
2.0
3.0
4.0
I Frequency stability vs. change in temperature, control voltage (Vc) = 1.65 Vdc.
Control voltage for (Fo) = 1.65 Vdc Typical. Positive Transfer Function.
When oscillator is disabled the pin 4 output is in a low state (Vol) and the pin 5 output is in the high state (VoH)
50 ohm termination into Vcc-2V or Thevein equivalent.
Specifications subject to change without notice.
9/29/06
Vs001
1
2
01
REV:
Copyright 2001 Connor-Winfield all rights reserved.
DATASHEET #:
PAGE
OF
DATE:
a