Capacitor Hardware
Type VR Vertical Mounting Clamp
Catalog Part Number
Unassembled
Dimensions
Assembled
Diameter
of Part to be
Mounted
Without
Screw & Nut
with
Screw & Nut
VR1A
VR3A
VR4A
VR6A
VR8A
VR10A
VR12A
—
A
B
C
Screw & Nut
VR1B
Included
VR1
VR3
VR4
VR6
VR8
VR10
VR12
—
1" to 1-1/16
1-3/8" to 1-7/16
1-1/2" to 1-9/16
1-3/4" to 1-13/16
2" to 2-1/16
2-1/2" to 2-9/16
3" to 3-1/8
Screw
1"
1-7/16"
1-7/8*"
VR3B
1-3/8" 1-25/32" 2-7/32"
1-1/2" 1-15/16" 2-11/32"
VR4B
VR6B
1-3/4" 2-1/4"
2" 2-1/2"
2-1/2" 3"
3" 3-7/16"
2-9/16"
2-13/16"
3-5/16"
3-13/16"
VR8B
VR10B
VR12B
VRSCREW
VRNUT
9/16" long 6-32 thread NC-2A
Nut
—
—
Standard hex nut to fit screws
CDE VR mounting clamps may be
VR1, 3 & 4
VR6, 8,10 & 12
used to mount any cylindrical ca-
pacitor with a 1” to 3” diameter
that is to be mounted in a verti-
cal position. Material is 1010 CRS,
commercial grade #4 temper ASI
scale. Parts are finished with .0001
(nominal) zinc chromate plating.
Use for mounting CG types, PSU, SF
and MPF types. Material thickness
is .035”
B Mtng 0.03”
.219”
.375”
.156”
C
0.01”
0.176”x 0.281”
0.016 (3 places).
B Mtg
120 º 3 º
(3 Places)
75 º
0.016”
2 Holes
.1561”Dia.
A
B Mtng 0.03”
.562”
.750”
Ø 0.201” 0.005”
0.375” 0.016”
0.075” 0.016”
Type TH Horizontal Mounting Clip
1.125” 0.016”
0.035”
Dimensions in Inches
Nominal Dia.
0.500” 0.016”
Catalog
Part Number
TH17
of Part to be
Mounted
0.625
A
B
C
0.312 0.720 0.015
These clips, though designed for
capacitors, have varied applica-
tions to retain many cylindrical
components. They are used ex-
tensively in the electrical and elec-
tronic industries to hold spindles,
condensers, capacitors, tubes,
rods and conduit. Clips have phos-
phate and oil finish.
TH25
1.375
0.312 1.500 0.030
Added tolerance to "C" dim.
(*) 0.340”execpt TH25 is 0.590”
t TH25 is 0.590".
(*)
(*) 0.340" excep
Material Thickness
TH17 is 0.016”, TH25
is 0.025”.
Material: 1050 high
carbon steel with
phosphate and oil
finish. TH25 is 1060.
Retaining tabs
Retaining tabs must
must extend
extend lower
B
than base of clip
lower than base
of clip
Material thickness TH13 thru TH17
is .016”. TH21 thru TH25 is .020”
C ±0.010"
A
0.594"
0.135" Dia. Hole
0.135”Dia. Hole
ACR15KT Motor Start Resistor Kit
ACR220KT Motor Run Resistor Kit
15K Ohm 2 watt bleeder resistors for AC motor start applica- 220K Ohm 1 watt bleeder resistors for AC motor run applica-
tions. Saves relay switch contacts and capacitor, particularly in tions. Saves relay switch contacts and capacitor, particularly in
capacitor start applications. 1/4” quick connect terminals elimi- capacitor run applications. 1/4” quick connect terminals elimi-
nate need for soldering.
nate need for soldering.
ACR15K:
ACR220K:
Pack of 10, 15K Ohm 2 watt bleeder resistor without quick con- Pack of 10, 220K Ohm 1 watt bleeder resistor without quick con-
nect terminals. nect terminals.
CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com