ELECTRICAL CHARACTERISTICS
Electrical characteristics apply over the full operating range of input voltage, output load (resistive) and baseplate temperature,
unless otherwise specified. All temperatures refer to the operating temperature at the center of the baseplate.
MODULE OPERATING SPECIFICATIONS
Parameter
Min
Typ
Max
425
500
Unit
Vdc
Vdc
Notes
Operating input voltage
Input surge withstand
250
375
<100ms
Output voltage setpoint
±1
% Vout nom.
Nominal input; full load; 25°C
MODULE OUTPUT VOLTAGE RELATED SPECIFICATIONS
Parameter
1.8V1 2V
2.5V2 3.3V
75
5V
12V
15V 24V 28V
48V
Unit
Notes
Efficiency (typ.)
71
72
77.7 81.5
84
110 150
200 300
86
87
87.5
89
%
Nominal input; 80% load; 25°C
Nominal input; full load;
25°C; 20MHz BW
Ripple and noise, p-p (typ.) 100
Output power (max.) 90
Output OVP setpoint (nom.) 2.7
100
100
2.7
100 100
114 150
140 190 130
300 300 300
170
300
mV
Watts
At 100°C baseplate temperature
25°C; recycle input voltage to
restart ( 1 minute off )
4.3
4.3
6.3 14.3 17.8 28.1 32.7
55.7
5.2
Volts
Dissipation, standby (typ.)
Load regulation (max.)
Current limit (typ.)
4.8
0.3
115
4.8
0.3
115
5.1
0.2
5.1
0.2
5.4
0.2
5.5
0.3
5.6
0.3
4.5
0.3
5.5
0.3
Watts
No load; nominal input
0.4 ±% Vout
No load to full load; nominal input
Output voltage 95% of nominal
115 115
115 115
115 115
115 115
115 115 115
115 115 115
115
115
% Iout
% Iout
Short circuit current (typ.)
115
115
Output voltage <250mV
MODULE INPUT SPECIFICATIONS
Parameter
Min
Typ
Max
Unit
Vdc
Vdc
Notes
Undervoltage turn-on
Undervoltage turn-off
242.5
212.2
247.5
204.7
492.2
Overvoltage turn-off/on
446.3
467.5
Vdc
MODULE OUTPUT SPECIFICATIONS
Parameter
Min
Typ
±0.02
±0.002
±2
Max
±0.20
±0.005
±5
Unit
%
Notes
Line regulation
Low line to high line; full load
Over operating temperature range
10 to 100% of full load
Temperature regulation
Power sharing accuracy
% / °C
%
Of nominal output voltage. For trimming below 90%
of nominal, a minimum load of 10% of maximum
rated power may be required.
10
110
Programming range
%
Note: For important information relative to applications where the converter modules are subject to continuous dynamic loading,
contact Vicor applications engineering at 800-927-9474.
1 Nominal 2V output trimmed to 1.8V by adding external 9,000 ohm resistor from the SC pin to
2 Nominal 3.3V output trimmed to 2.5V by adding external 3,125 ohm resistor from the SC pin to
-
S pin. (See Fig. 7)
-S pin. (See Fig. 7)
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715
375V Mini Family
Rev. 6.4
Page 2 of 8
Set your site on VICOR at www.vicorpower.com