Automotive Relays
Plug-in Mini ISO Relays
Power Relay B
n
n
n
Pin assignment similar to ISO 7588 part 1
Plug-in terminals
Customized versions on request
– 24VDC versions with contact gap >0.8mm
– Integrated components (e.g. resistor, diode)
– Customized marking/color
– Special covers (e.g. notches, release features, brackets)
– Various contact arrangements and materials
Typical applications
Cross carline up to 35A for example: rear window defogger, battery
disconnection, power distribution (clamp 15)
F234_fcw1_bw
Contact Data
Contact arrangement
1 A
1 form A,
1 NO
1 A
1 form A,
1 NO
1 C
1 form C,
1 CO
1 C
1 form C,
1 CO
Rated voltage
12VDC
24VDC
12VDC
24VDC
Coil Data
Limiting continuous current
form A/form B (NO/NC)
23°C
Rated coil voltage
12/24VDC
Coil
50A
35A
15A
50A
35A
15A
50/35A
35/25A
15/10A
50/35A
35/25A
15/10A
Coil versions, DC coil
Coil
code
85°C
Rated
voltage
VDC
12
12
24
Operate
voltage
VDC
8
6.5
16
Release
voltage
VDC
1.5
1
3
Rated coil
125°C
resistance 5) power 5)
Limiting making current1)
Ω 10ꢀ
85
75
W
A/B (NO/NC)
Limiting breaking current,
A/B (NO/NC)
120A
30A
120A
20A
120/45A
30/20A
120/45A
20/10A
001
002
004
1.7
1.9
2.3
255
5) Without components in parallel.
All figures are given for coil without pre-energization, at ambient temperature +23°C.
Limiting short-time current
overload current, ISO 8820-3 2)
1.35 x 35A, 1800s
2.00 x 35A, 5s
3.50 x 35A, 0.5s
6.00 x 35A, 0.1s
24VDC for 5min,
Insulation Data
Initial dielectric strength
Jump start test, ISO 16750-1
between open contacts
between contact and coil
between adjacent contacts
Load dump test
ISO 7637-1 (12VDC), test pulse 5
ISO 7637-2 (24VDC), test pulse 5
500Vrms
500Vrms
500Vrms
conducting nominal current at 23°C
Silver based
Contact material
Min. recommended contact load3)
Initial voltage drop, at 10A, typ./max.
1A at 5VDC
Vs=+86.5VDC
Vs=+200VDC
form A (NO)
form B (NC)
15/300mV 15/300mV 15/300mV 15/300mV
-
-
20/300mV 20/300mV
6 ops./min (0.1Hz)
10/10ms4)
Frequency of operation, at nominal load
Operate/release time typ.
Other Data
Electrical endurance, ops.
EU RoHS/ELV compliance
Protection to heat and fire according UL94
Ambient temperature
compliant
HB or better6)
-40 to 125°C
resistive load, A (NO) >2.5x105
>2.5x105
20A,
>2.5x105
30A,
>2.5x105
20A,
30A,
14VDC
28VDC
-
14VDC
28VDC
>2.5x105
10A,
Climatic cycling with condensation,
EN ISO 6988
Temperature cycling,
IEC 60068-2-14, Nb
Damp heat cyclic,
resistive load, B (NC)
Mechanical endurance
-
>1x105
6 cycles, storage 8/16h
20A,
14VDC
28VDC
10 cycles, -40/+85°C (5°C/min)
typ. 1x106 ops.
1) The values apply to a resistive or inductive load with suitable spark suppression and
at maximum 14VDC for 12VDC or 28VDC for 24VDC load voltages. For a load current
duration of maximum 3s for a make/break ratio of 1:10.
2) Current and time are compatible with circuit protection by a typical automotive fuse.
Relay will make, carry and break the specified current.
3) See chapter Diagnostics of Relays in our Application Notes or consult the internet at
http://relays.te.com/appnotes/
4) For unsuppressed relay coil. A low resistive suppression device in parallel to the relay
coil increases the release time and reduces the lifetime caused by increased erosion
and/or higher risk of contact tack welding.
IEC 60068-2-30, Db, Variant 1
6 cycles, upper air temp. 55°C
Damp heat constant, IEC 60068-2-3, Ca
Category of environmental protection,
IEC 61810
Degree of protection, IEC 60529
Corrosive gas
IEC 60068-2-42
IEC 60068-2-43
Vibration resistance (functional)
IEC 60068-2-6 (sine sweep)
Shock resistance (functional)
IEC 60068-2-27 (half sine)
Drop test, free fall, IEC 60068-2-32
56 days
RT I – dustproof
IP54
10 2cm3/m3 SO2, 10 days
1 0.3cm3/m3 H2S, 10 days
10 to 500Hz, min. 5g7)
11ms, min. 20g7)
1m onto concrete
1
06-2011, Rev. 0611
Datasheets and product specification ac-
cording to IEC 61810-1 and to be used only
together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
www.te.com
© 2011 Tyco Electronics Corporation,
a TE Connectivity Ltd. company.
5秒后页面跳转
解析光耦仿真器：升级光耦合器技术的必要性
英伟达新一代Blackwell GPU过热问题致交付延迟
国产厂商思特威CMOS图像传感器芯片单月出货超1亿颗，技术创新引领行业发展
台积电5nm和3nm产能利用率达100%，半导体行业景气度持续攀升
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
