5秒后页面跳转
V23076A1022C133 PDF预览

V23076A1022C133

更新时间: 2024-12-01 12:52:51
品牌 Logo 应用领域
其他 - ETC /
页数 文件大小 规格书
4页 889K
描述
Limiting continuous current 45A

V23076A1022C133 数据手册

 浏览型号V23076A1022C133的Datasheet PDF文件第2页浏览型号V23076A1022C133的Datasheet PDF文件第3页浏览型号V23076A1022C133的Datasheet PDF文件第4页 
Automotive Relays  
PCB Single Relays  
Power Relay K (Open – Sealed)  
n
n
n
n
Limiting continuous current 45A  
Wide voltage range  
24VDC coil versions available  
For high current version refer to Power Relay K-S  
Typical applications  
ABS control, blower fans, car alarm, cooling fan, engine control, fuel pump,  
hazard warning signal, heated front screen, heated rear screen, ignition,  
lamps front/rear/fog light, interior lights, main switch/supply relay, seat  
control, seatbelt pretensioner, sun roof, turn signal, valves, window lifter,  
wiper control.  
Contact Data  
Typical applications  
Resistive/inductive  
loads  
1 form A, 1 NO  
12VDC  
Resistive/inductive  
loads  
1 form C, 1 CO  
12VDC  
Indicator lamps  
Headlights,  
capacitive loads  
1 form A, 1 NO  
12VDC  
Headlights  
capacitive loads  
1 form C, 1 CO  
12VDC  
Contact arrangement  
Rated voltage  
1 form A, 1 NO  
12VDC  
A/B (NO/NC)  
45/30A  
A/B (NO/NC)  
40/25A  
Rated current  
Limiting continuous current  
23°C  
45A  
30A  
40A  
45A  
30A  
100A  
60A  
AgNi0.15  
45/30A  
30/25A  
100/30A  
60/30A  
30A  
25A  
40A  
25A  
180A  
60A  
40/25A  
25/20A  
180/60A  
60/30A  
AgSnO2  
85°C  
Limiting making current1)  
Limiting breaking current2)  
Contact material  
120A3)  
60A  
AgNi0.15  
AgSnO2  
AgSnO2  
Min. recommended contact load  
Initial voltage drop, at 10A, typ./max.  
Operate/release time  
Electrical endurance  
1A at 5VDC4)  
20/300mV  
typ. 5/3ms5)  
>2x105 ops.  
at 13.5VDC, 40A  
>2x105 ops.  
at 13.5VDC, 40A  
>107 ops.  
>2.2x106 ops.  
up to 8x21W  
>105 ops.  
up to 4x60W  
>105 ops.  
up to 4x60W  
Mechanical endurance, DC coil  
1) The values apply to a resistive or inductive load with suitable spark suppression and at maximum 13.5VDC for 12VDC or 27VDC for 24VDC load voltages.  
2) For a load current duration of maximum 3s for a make/break ratio of 1:10.  
3) Corresponds to a peak inrush current on initial actuation (cold filament).  
4) See chapter Diagnostics of Relays in our Application Notes or consult the internet at http://relays.te.com/appnotes/  
5) For unsuppressed relay coil. A low resistive suppression device in parallel to the relay coil increases the release time and reduces the lifetime caused by increased erosion and/or higher  
risk of contact tack welding.  
Max. DC load breaking capacity  
TE0556-E  
Load limit curve 1: arc extinguishes, during transit time (changeover contact).  
Load limit curve 2: safe shutdown, no stationary arc (make contact).  
Load limit curves measured with low inductive resistors verified for 1000 switching events.  
1
06-2011, Rev. 0611  
Datasheets and product specification ac-  
cording to IEC 61810-1 and to be used only  
together with the ‘Definitions’ section.  
Datasheets and product data is subject to the  
terms of the disclaimer and all chapters of  
the ‘Definitions’ section, available at  
http://relays.te.com/definitions  
Datasheets, product data, ‘Definitions’ sec-  
tion, application notes and all specifications  
are subject to change.  
www.te.com  
© 2011 Tyco Electronics Corporation,  
a TE Connectivity Ltd. company.