ALUMINUM ELECTROLYTIC CAPACITORS
4.5mmL Chip Type
ZS series
WX
Chip type with 4.5mm height.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2002/95/EC).
Smaller
High
Bi-polarized
ZT
ZP
Temperature
Z S
Smaller
Specifications
ZR
Item
Performance Characteristics
Temperature Range
Category
–40 to + 85°C
4 to 50V
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
0.1 to 220µF
+
20% at 120Hz, 20°C
–
After 2 minutes' application of rated voltage leakage current is not more than 0.01 CV or 3 (µA) ,whichever is greater.
,
Measurement frequency : 120Hz Temperature : 20°C
,
Rated voltage (V)
4
6.3
10
16
25
35
50
Tangent of loss angle (tan δ)
tan δ (MAX.)
0.50
0.30
0.24
0.19
0.16
0.14
0.14
Measurement frequency : 120Hz
4
7
6.3
4
10
3
16
25
2
35
2
50
2
Rated voltage (V)
Stability at Low Temperature
2
4
Z–25°C / Z+20°C
Z–40°C / Z+20°C
Impedance ratio
ZT / Z20 (MAX.)
15
8
8
4
3
3
+
Capacitance change
tan δ
Within 20% of the initial capacitance value
–
The specifications listed at right shall be met when
the capacitors are restored to 20°C after the rated
voltage is applied for 2000 hours at 85°C.
200% or less than the initial specified value
Less than or equal to the initial specified value
Endurance
Shelf Life
Leakage current
After storing the capacitors under no load at 85°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds, which is
+
Capacitance change
tan δ
Within 10% of the initial capacitance value
–
Resistance to soldering
heat
maintained at 250°C. The capacitors shall meet the
characteristic requirements listed at right when they are
removed from the plate and restored to 20°C.
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Leakage current
Marking
Black print on the case top.
Type numbering system (Example : 16V 10 F)
µ
Chip Type
Positive
1
2
3
4
5
6
7
8
9 10 11 12 13 14
Capacitance
U Z S 1 C 1 0 0 M C L 1 G B
Plastic platform
+
Voltage
Lot No.
0.3 MAX.
C
0.2
–
Taping code
(mm)
6.3
1.8 2.1 2.4
4.3 5.3 6.6
4.3 5.3 6.6
1.0 1.3 2.2
Configuration
φD
A
B
C
E
4
5
+
Capacitance tolerance ( 20%)
–
Rated capacitance (10µF)
Rated voltage (16V)
Series name
+0.1
–0.2
4.5
Negative
0.5 to 0.8
Voltage mark for 6.3V is 6V
.
Type
Dimensions
4
6.3
10
1A
16
25
35
50
V
Cap. (µF)
Code
0G
0J
1C
1E
1V
1H
0.1
0.22
0.33
0.47
1
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
101
221
4
1.0
2.0
2.8
4.0
8.4
4
4
4
4
2.2
3.3
4.7
4
13
4
17
20
33
4
16
27
42
52
4
18
29
46
5
10
4
23
37
49
58
5
5
6.3
22
33
4
28
37
45
70
5
33
5
6.3
6.3
6.3
4
28
33
56
96
5
5
41
52
6.3
6.3
47
4
5
6.3
100
220
5
6.3
Rated
ripple
Case size
φ D (mm)
6.3
Rated ripple current (mArms) at 85°C 120Hz
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given
in page 18, 19.
Please select UR(p.104), UG(p.110) series if high C/V
products are reqired.
Frequency coefficient of rated ripple current
Frequency
50 Hz
120 Hz
300 Hz
1 kHz
10 kHz or more
1.50
Coefficient
0.70
1.00
1.17
1.36
Please refer to page 3 for the minimum order quantity.
CAT.8100A