ALUMINUM ELECTROLYTIC CAPACITORS
12.5mmL MAX.
RUseries
RY
Laminated case series.
12.5mmL MAX. height.
High
Temperature
RU
Specifications
Item
Performance Characteristics
Category
- 40~+85°C(6.3V~400V), - 25~+85°C(450V)
6.3~450V
Temperature Range
Rated
Rated
Voltage Range
6.8~6800µF
Capacitance Range
±20% at 120Hz, 20°C
Capacitance Tolerance
Rated voltage(V)
6.3~100V
160~450V
After 1 minute's application of rated voltage, leakage current
is not more than 0.03CV or 4 (µA), whichever is greater.
Leakage Current
After 1 minute's application of rated voltage,
I
=0.04CV+100(µA) or less
After 2 minutes' application of rated voltage, leakage current
is not more than 0.01CV or 3 (µA), whichever is greater.
µF
µF
.
For capacitance of more than 1000 , add 0.02 for every increase of 1000
Measurement frequency : 120Hz, Temperature : 20°C
Rated voltage(V)
tan δ(MAX.)
6.3
0.28
10
0.24
16
0.20
25
0.16
35
0.14
50
0.12
63
0.12
100
0.12
160~350 400~450
0.20 0.25
tan
δ
Measurement frequency : 120Hz
6.3
5
12
10
4
10
16
3
8
25
2
5
35
2
4
50~100 160~200 250~350 400
450
15
—
Rated voltage(V)
Z - 25°C/Z+20°C
Z - 40°C/Z+20°C
Stability at Low Temperature
Endurance
2
3
3
4
4
8
6
10
Impedance ratio
ZT/Z20(MAX)
After 2000 hours' application of rated voltage
at 85°C,capacitors meet the characteristic
requirements listed at right.
Capacitance change
tan δ
Within ±20% of initial value
200% or less of initial specified value
Initial specified value or less
Leakage current
After leaving capacitors under no load at 85°C for 1000 hours, they meet the specified value for
endurance characteristics listed above.
Shelf Life
Marking
Black print on the case top.
Type numbering system (Example : 10V 2200µF)
Radial Lead Type
1
2
3
4
5
6
7
8
9
10 11
φd
Laminated case
Capacitance
U R U 1 A 2 2 2 M H R
Voltage
Trade
mark
Configuration
φD
12.5~18
Code
HR
Capacitance tolerance(±20%)
Rated Capacitance(2200µF)
Rated voltage(10V)
Series name
20~25
RR
Series
Lot No.
Pressure
relief vent
MIN
MIN
4
15
MAX
L+
Type
The PET sleeve product is also available upon request.
•
In this case, T will be put at 11th digit of type numbering system.
φD 12.5 16
18
7.5
0.8
20
22
10 12.5
1.0 1.0
25
(φD < 20)1.5
(φD 20)2.0
P
5.0
0.6
7.5
0.8
10
φd
1.0
Please refer to page 18, 19, 20 about the formed or taped product spec.
Please refer to page 3 for the minimum order quantity.
Dimension table in next page.
CAT.8100Q-1