5秒后页面跳转
捷配首页

Datasheet > UCC38084DG4
UCC38084DG4 PDF预览

UCC38084DG4

更新时间： 2024-11-28 12:01:43
品牌 Logo 应用领域
德州仪器 - TI /
页数 文件大小 规格书
27页 918K
描述
8-PIN CURRENT MODE PUSH-PULL PWM CONTROLLERS WITH PROGRAMMABLE SLOPE COMPENSATION

阅读下载

中文翻译

获取价格

UCC38084DG4 数据手册

 浏览型号UCC38084DG4的Datasheet PDF文件第2页浏览型号UCC38084DG4的Datasheet PDF文件第3页浏览型号UCC38084DG4的Datasheet PDF文件第4页浏览型号UCC38084DG4的Datasheet PDF文件第5页浏览型号UCC38084DG4的Datasheet PDF文件第6页浏览型号UCC38084DG4的Datasheet PDF文件第7页 
ꢀ
ꢀ
ꢁ
ꢁ
ꢁ
ꢁ
ꢂ
ꢅ
ꢃ
ꢃ
ꢄ
ꢄ
ꢃ
ꢃ
ꢅ
ꢅ
ꢆ
ꢆ
ꢀ
ꢀ
ꢁ
ꢁ
ꢁ
ꢁ
ꢂ
ꢅ
ꢃ
ꢃ
ꢄ
ꢄ
ꢃ
ꢃ
ꢇ
ꢇ
ꢆ
ꢆ
ꢀ
ꢀ
ꢁ
ꢁ
ꢁ
ꢁ
ꢂ
ꢅ
ꢃ
ꢃ
ꢄ
ꢄ
ꢃ
ꢃ
ꢈ
ꢈ
ꢆ
ꢆ
ꢀ
ꢀ
ꢁ
ꢁ
ꢁ
ꢁ
ꢂ
ꢅ
ꢃ
ꢃ
ꢄ
ꢄ
ꢃ
ꢃ
ꢉ
ꢉ
SLUS488E − SEPTEMBER 2002 − REVISED JULY 2009  
ꢃ
ꢊ
ꢋ
ꢌ
ꢍ
ꢁ
ꢀ
ꢎ
ꢎ
ꢏ
ꢍ
ꢐ
ꢑ
ꢒ
ꢓ
ꢏ
ꢋ
ꢀ
ꢔ
ꢕ
ꢊ
ꢋ
ꢀ
ꢖ
ꢖ
ꢋ
ꢗ
ꢑ
ꢁ
ꢒ
ꢍ
ꢐ
ꢎ
ꢒ
ꢖ
ꢖ
ꢏ
ꢎ
ꢔ
ꢗ
ꢌ
ꢐ
ꢕ
ꢋ
ꢎ
ꢒ
ꢘ
ꢎ
ꢙ
ꢑ
ꢑ
ꢙ
ꢚ
ꢖ
ꢏ
ꢔ
ꢖ
ꢒ
ꢋ
ꢏ
ꢁ
ꢒ
ꢑ
ꢋ
ꢏ
ꢍ
ꢔ
ꢙ
ꢐ
ꢌ
ꢒ
ꢍ
FEATURES  
APPLICATIONS  
D
D
D
D
Programmable Slope Compensation  
D
D
D
D
High-Efficiency Switch-Mode Power Supplies  
Telecom dc-to-dc Converters  
Internal Soft-Start on the UCC38083/4  
Cycle-by-Cycle Current Limiting  
Point-of-Load or Point-of-Use Power Modules  
Low Start-Up Current of 120 µA and 1.5 mA  
Typical Run Current  
Low-Cost Push-Pull and Half-Bridge  
Applications  
D
D
Single External Component Oscillator  
Programmable from 50 kHz to 1 MHz  
DESCRIPTION  
The UCC38083/4/5/6 is a family of BiCMOS pulse width  
modulation (PWM) controllers for dc-to-dc or off-line  
fixed-frequency current-mode switching power  
supplies. The dual output stages are configured for the  
push-pull topology. Both outputs switch at half the  
oscillator frequency using a toggle flip-flop. The dead  
time between the two outputs is typically 110 ns, limiting  
each output’s duty cycle to less than 50%.  
High-Current Totem-Pole Dual Output Stage  
Drives Push-Pull Configuration with 1-A Sink  
and 0.5-A Source Capability  
D
Current Sense Discharge Transistor to  
Improve Dynamic Response  
D
Internally Trimmed Bandgap Reference  
Undervoltage Lockout with Hysteresis  
D
The new UCC3808x family is based on the UCC3808A  
architecture. The major differences include the addition  
of a programmable slope compensation ramp to the CS  
signal and the removal of the error amplifier. The current  
flowing out of the ISET pin through an external resistor  
is monitored internally to set the magnitude of the slope  
compensation function. This device also includes an  
OUT internal discharge transistor from the CS pin to ground,  
which is activated at each clock cycle after the pulse is  
terminated. This discharges any filter capacitance on  
the CS pin during each cycle and helps minimize filter  
capacitor values and current sense delay.  
BASIC APPLICATION  
V
IN  
POWER  
TRANSFORMER  
V
VDD  
UCC3808x  
CTRL OUTA  
The UCC38083 and the UCC38084 devices have a  
typical soft-start interval time of 3.5 ms while the  
UCC38085 and the UCC38086 has less than 100 µs for  
applications where internal soft-start is not desired.  
RT  
OUTB  
CS  
R
F
ISET  
The UCC38083 and the UCC38085 devices have the  
turn-on/off thresholds of 12.5 V / 8.3 V, while the  
UCC38084 and the UCC38086 has the turn-on/off  
thresholds of 4.3 V / 4.1 V. Each device is offered in 8-pin  
TSSOP (PW), 8-pin SOIC (D) and 8-pin PDIP (P)  
packages.  
GND  
R
T
R
S
R
SET  
C
F
FEEDBACK  
UDG−01080  
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments  
semiconductor products and disclaimers thereto appears at the end of this data sheet.  
ꢋ
ꢎ
ꢒ
ꢓ
ꢀ
ꢁ
ꢐ
ꢌ
ꢒ
ꢍ
ꢓ
ꢙ
ꢐ
ꢙ
ꢛ
ꢜ
ꢝ
ꢞ
ꢟ
ꢠ
ꢡ
ꢢ
ꢛ
ꢞ
ꢜ
ꢛ
ꢣ
ꢤ
ꢥ
ꢟ
ꢟ
ꢦ
ꢜ
ꢢ
ꢡ
ꢣ
ꢞ
ꢝ
ꢧ
ꢥ
ꢨ
ꢩ
ꢛ
ꢤ
ꢡ
ꢢ
ꢛ
ꢞ
ꢜ
ꢪ
ꢡ
ꢢ
ꢦ
ꢫ
Copyright 2002−2009, Texas Instruments Incorporated  
ꢋꢟ ꢞ ꢪꢥꢤ ꢢ ꢣ ꢤ ꢞꢜ ꢝꢞ ꢟ ꢠ ꢢ ꢞ ꢣ ꢧꢦ ꢤ ꢛꢝ ꢛꢤꢡ ꢢꢛ ꢞꢜꢣ ꢧꢦ ꢟ ꢢꢬ ꢦ ꢢꢦ ꢟ ꢠꢣ ꢞꢝ ꢐꢦꢭ ꢡꢣ ꢌꢜꢣ ꢢꢟ ꢥꢠ ꢦꢜꢢ ꢣ  
ꢣ ꢢ ꢡ ꢜꢪ ꢡ ꢟꢪ ꢮ ꢡ ꢟꢟ ꢡ ꢜ ꢢꢯꢫ ꢋꢟ ꢞ ꢪꢥꢤ ꢢꢛꢞꢜ ꢧꢟ ꢞꢤ ꢦꢣ ꢣꢛ ꢜꢰ ꢪꢞꢦ ꢣ ꢜꢞꢢ ꢜꢦ ꢤꢦ ꢣꢣ ꢡꢟ ꢛꢩ ꢯ ꢛꢜꢤ ꢩꢥꢪ ꢦ  
ꢢ ꢦ ꢣ ꢢꢛ ꢜꢰ ꢞꢝ ꢡ ꢩꢩ ꢧꢡ ꢟ ꢡ ꢠ ꢦ ꢢ ꢦ ꢟ ꢣ ꢫ  
1
www.ti.com  
1234567...27

中文翻译

下载PDF

UCC38084DG4 替代型号

型号 品牌 替代类型 描述 数据表
UCC38084DRG4 TI

完全替代

 8-PIN CURRENT MODE PUSH-PULL PWM CONTROLLERS WITH PROGRAMMABLE SLOPE COMPENSATION
UCC38084DR TI

完全替代

 8-PIN CURRENT MODE PUSH-PULL PWM CONTROLLERS WITH PROGRAMMABLE SLOPE COMPENSATION
UCC38084D TI

类似代替

 8-PIN CURRENT MODE PUSH-PULL PWM CONTROLLERS WITH PROGRAMMABLE SLOPE COMPENSATION

与UCC38084DG4相关器件

型号 品牌 获取价格 描述 数据表
UCC38084DR TI

获取价格

 		8-PIN CURRENT MODE PUSH-PULL PWM CONTROLLERS WITH PROGRAMMABLE SLOPE COMPENSATION
UCC38084DRG4 TI

获取价格

 		8-PIN CURRENT MODE PUSH-PULL PWM CONTROLLERS WITH PROGRAMMABLE SLOPE COMPENSATION
UCC38084P TI

获取价格

 		8-PIN CURRENT MODE PUSH-PULL PWM CONTROLLERS WITH PROGRAMMABLE SLOPE COMPENSATION
UCC38084PG4 TI

获取价格

 		8-PIN CURRENT MODE PUSH-PULL PWM CONTROLLERS WITH PROGRAMMABLE SLOPE COMPENSATION
UCC38084PW TI

获取价格

 		8-PIN CURRENT MODE PUSH-PULL PWM CONTROLLERS WITH PROGRAMMABLE SLOPE COMPENSATION
UCC38084PWG4 TI

获取价格

 		8-PIN CURRENT MODE PUSH-PULL PWM CONTROLLERS WITH PROGRAMMABLE SLOPE COMPENSATION
UCC38084PWR TI

获取价格

 		8-PIN CURRENT MODE PUSH-PULL PWM CONTROLLERS WITH PROGRAMMABLE SLOPE COMPENSATION
UCC38084PWRG4 TI

获取价格

 		8-PIN CURRENT MODE PUSH-PULL PWM CONTROLLERS WITH PROGRAMMABLE SLOPE COMPENSATION
UCC38085 TI

获取价格

 		8-PIN CURRENT MODE PUSH-PULL PWM CONTROLLERS WITH PROGRAMMABLE SLOPE COMPENSATION
UCC38085D TI

获取价格

 		8-PIN CURRENT MODE PUSH-PULL PWM CONTROLLERS WITH PROGRAMMABLE SLOPE COMPENSATION

与UCC38084DG4相关文章

您还可以找


热门产品
PCB打样/小批量
铝基板
BOM智能配单
PCBA制造
钣金
精密CNC
模具注塑
薄膜开关
精选活动
PCBA打样特惠
四六层板品质升级
铝基板品质升级
一体化电子制造
DFM下载
服务支持
企业认证
产品展示
工厂展示
工艺能力
积分商城
关于捷配
捷配简介
企业文化
公司动态
人才招聘
联系我们
帮助中心
下单流程
付款流程
开票流程
常见问题
全球PCB制造服务专线 400-613-0088

工作时间：9:00-21:00

CEO邮箱：ceo@jiepei.com

投诉邮箱：tousu@jiepei.com

捷配网-微信公众号 微信公众号
捷配网-微信公众号 抖音公众号
资质认证：
合作快递：
支付方式：
Copyright © 2024 Jiepei.com Inc. All Rights Reserved. 版权所有:杭州捷配信息科技有限公司 浙公网安备 33010502006866号 浙ICP备10014259号-119 营业执照ICP证