TRC-150W Dimmable Series
Switch Mode LED Drivers
Constant Current
Aluminum Housing
Electrical Specifications
Input Voltage Range:
100 - 277 Nom. Vac (90 - 305 V Min/Max)
Frequency:
50/60 Hz Nom. (47-63 Hz Min/Max)
>0.90 @ full load, 100V through 277V
Power Factor:
Inrush Current:
Input Current:
65 Amps maximum @ 230 Vac, cold start 25ºC
1.8 A max 100Vac, 0.9 A max 220Vac
Maximum Power:
Line Regulation:
Load Regulation:
Leakage Current:
Typical Efficiency
Turn-on Delay:
Ripple and Noise:
Protection:
150W
± 1%
± 3%
0.75 mA 277 Vac 60Hz
92.5%-93.5% at 220Vac
0.5S typical 110Vac, 0.3S typical 220Vac
13V at 350 mA
Over-Voltage, Over-Temperature (110°C), Lightning,
and Short Circuit Protection with Self Recovery
• Total Power: 150 Watts
• Input Voltage: 100-277 Vac Nom.
• UL Dry & Damp Location Rated
• IP67
Environmental Specifications
Minimum Starting Temp: -35ºC
• Ultra-high Efficiency
• High Power Factor with Active Correction
• UL8750
Storage Temperature:
Humidity:
-40ºC to +85ºC
5% to 100%
Convection
Class A
Cooling:
Sound Rating:
MTBF:
250,000 Hours (350 mA model) @ 110Vac input, 80%
load and 25ºC ambient conditions per MIL-HDBK-217F
230,000 Hours (1400 mA model) @ 110Vac input, 80%
load and 25ºC ambient conditions per MIL-HDBK-217F
Lifetime:
Weight:
350mA: 58,000 Hours @ 220Vac, 80% load, Tc=60ºC
1400mA: 88,000 Hours @ 220Vac, 80% load, Tc=60ºC
3.31 lbs. (1.5 kg)
Dimming - Product Specifications
New Surge Protection and HI-POT Testing
Output Current Output Voltage Max. Output
Typical
Model Number
(mA)*
Range (Vdc)
214~428
166~333
107~214
107~142
53~107
Power (W) Efficiency
TRC-150S035DT
TRC-150S045DT
TRC-150S070DT
TRC-150S105DT
TRC-150S140DT
350
150
150
150
150
150
93.5%
93.0%
93.0%
93.0%
92.5%
450
700
Metal Lock Sheet
Nut
1050
1400
* The output current is adjustable at factory from 50% to 100%.
HI-POT Test
Normal Application
The new design of this LED driver provides 1.4KV surge protection. To properly
HI-POT test this unit, the surge protection must be disconnected. The screw, nut, and
metal lock sheet on the input side of the driver provide for this. To test, first remove
the nut and lock sheet as shown. After testing, secure the nut and lock sheet to
provide line-to-earth protection.
This HI-POT test feature is available on product manufactured after August 15, 2015.
E332160
Note:
LED drivers are designed and intended to operate LED loads only.
Non-LED loading may be outside the specified design limits of our
LED drivers, and therefore cannot be covered by any warranty.
If you desire to use our LED drivers to operate non-LED loads
please contact us to discuss compatibility.
Specifications subject to change without notice.
Rev 9-1-15
Thomas Research Products • 1225 Bowes Rd • Elgin, IL 60123 • T 847-515-3057 • F 847-515-3047 • www.trpssl.com